Multitool file blades: worth having?
-
I think smoothing out a fingernail has been my number 1 use for a file blade.

-
Nails, burrs, sharpening a kitchen knife to something better than it was at my gran's,
Plastic cutting, prodding, ... -
If it's good--all modern Vic, most LM, and most standard Gerber do. The diamond file is really great.
SOG files suck, as well as nearly all low-end tools due to cheap steel used, and often being stamped and not cut.
-
I've used the file on my Charge TTi quite a bit. Most of the uses are on plastic though (3D printed parts mostly), just to widen an opening, smooth out some edges, radius corners, ect. I have also used it on sheet metal after I've made a cut, and I have cut the odd screw or nail. I just used the diamond file on the wheel hexes on my new SCX10 III so my new rims would fit on them as they had a tighter tolerance than the stock rims, and it worked a treat.
-
That's a cool use!

-
A very good question that got me thinking
(never a good thing in itself :ahhh )If memory serves; the one and only time I had cause to use a file (MT based) was on my original Mini way back in about 1989

My bike was trapped in the back garden of a shared house. In my absence someone had put a padlock on the back gate and my little Kawasaki was behind it (the house was also devoid of anyone with a key, or knowledge thereof) ::)
I hunted high and low for a suitably heavy implement to remove the offending article but to no avail then; inspiration

I could use the file on my LM Mini

It took me over 30mins of
swearingeffort but luck was a lady that night (so was the need to exit) >:D
Success (two out of two)
That aside I used the one on my now defunct/lost Paratool, mid 90's, it broke (not approved usage
) -
@derekmac said:
I just used the diamond file on the wheel hexes on my new SCX10 III so my new rims would fit on them as they had a tighter tolerance than the stock rims, and it worked a treat.This brings up a question:
If I need a file, I usually grab a dedicated (properly hardened) file or diamond stone off the workbench. Did you use your multitool because you didn't have access to a dedicated file? Was it more convenient? Or did it seem 'just as good as' a dedicated file?
-
@Nix said:
This brings up a question:If I need a file, I usually grab a dedicated (properly hardened) file or diamond stone off the workbench. Did you use your multitool because you didn't have access to a dedicated file? Was it more convenient? Or did it seem 'just as good as' a dedicated file?
The charge was beside me, so that's what I grabbed. The hexes are aluminium, so very easy to take material off, and the diamond file (IMHO) had the perfect amount of bite to do the job without worry of removing too much material. I have a drawer full of different files, from ones that could reprofile the cutting edge of a dozer (well maybe not, lol) to ones that are a 1/4 the size of the LM file.
Holding the Charge and using the file was also very comfortable. The smaller files that I have that would have been proper to use for this task would not have been as comfortable to use. Bigger files that are more comfortable to use would have been harder to hold and control.
-
-
On a MT yes. The compromise is there but the utility of having a file is what having a MT with file is all about. I asked the question about MT files being like "real" files. I recall the question being brought up a while ago. I've used my file on my Wave and Charge mostly to knock down metal edges. Materials like aluminum and sheet metal mostly. These edges come up randomly so having a way to sand them down then and there is nice. I've cut and shaped with it too. Sure a dedicated tool is great but for me my MT needs to come off the bench and perform when called. I don't know when those moments will arise but its why I carry my Charge, I'm usually ready for whatever.
/post/1173362
-
@Nix said:
I agree that the diamond file has some value.What have you used your file(s) for?
I've used the SwissTool file for general filing, and cutting of non-hardened metals. I had to remove a rotted post, had forgotten my fence pliers, and the linesman's pliers I had were old, and wouldn't cut the thick wire. Had it cut through in just a few minutes by sawing through the staves with the ST file. Notching, as well as removing carbon from spark plugs and electrical contacts is another big use.
I've often used the diamond file on LM for hardened steel. I have ground down the kicks on several old, beat up traditional folders so the tip wouldn't stick up from the handle. If I encounter a dull or chipped garden tool, I'll sharpen it up with the diamond file.
-
I don't use the file all the time, but it has been useful many times
Mostly for adjusting fittings and deburring sheetmetal and sometimes I find them useful to file a socket that I have beaten so it won't fit my ratchet and usually the MT file is all that fits 
Sent fra min FRD-L09 via Tapatalk
-
I wore the diamond file on my wave smooth in my last job as it involved fitting kitchens and building furniture both from scratch and flat pack. And I was always coming across machine screws that were too long that ether required filing down a fraction or cutting and then cleaning up the end with a file.
This is why I wish waves came with a replaceable file/saw.
-
I use a file (both MT and dedicated) quite often
I use them when we are working with smooth cut stones like Indiana limestone and the like
I am the stone patcher on our jobs (among many other things ;) )and I have plenty of dedicated files, rasps, sandpaper and some other things for stone but having a small file with me is very handy if I am going through and just patching small chips
I use the regular file side, if using a diamond file, to smooth
dges down and take burrs off as well 
I use a file for many other uses as well. I use one as a fingernail file, the diamond side as a knife sharpener, debur tools and smooth things down in general at both work and home

I like the Vic files on both the 91mm and 74mm range but my favorite file is the Leatherman diamond file
it has a greater range of uses for me and that is why I included it in my Charge knife mod 
I voted 6 because I do carry MTs sometimes without a file, so it isn't a total deal breaker for me but I try to have my Charge knife with me to make up for it
of course a challenge always makes that a part a bit harder if the MT in it doesn't have a file
;) -
Also, I just really like files
:D -
They are useful as it is one of the tools that you are not likely to have on you.
however, not all files are equal
-
I vote 6 and 7 and get rid of the smurfing can openers already :D
-
Heresy!!!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


Necessity is the mother of invention (and hormones)