One handed Spirit, the MXBS
-
This is definitely one that I know a lot of people have been waiting for! I don't think the tabs look like they're going to be massively in the way.
-
First impression
Just unpacked them. Getting it out of the sheath was very difficult.
The tabs are not sharp, but they stand very proud, so there is a good chance they generate some nasty pressure points in the pockets. Also, not a fan of the blade-grind. That said, they work very well.Will carry it for a while, but I'm almost certain that the benefit (OHO) does not outweigh the drawbacks (blade-grind, hot-spots).


-
@Etherealicer said:
First impressionJust unpacked them. Getting it out of the sheath was very difficult.
The tabs are not sharp, but they stand very proud, so there is a good chance they generate some nasty pressure points in the pockets. Also, not a fan of the blade-grind. That said, they work very well.Will carry it for a while, but I'm almost certain that the benefit (OHO) does not outweigh the drawbacks (blade-grind, hot-spots).

-
@Etherealicer said:
First impressionJust unpacked them. Getting it out of the sheath was very difficult.
The tabs are not sharp, but they stand very proud, so there is a good chance they generate some nasty pressure points in the pockets. Also, not a fan of the blade-grind. That said, they work very well.Will carry it for a while, but I'm almost certain that the benefit (OHO) does not outweigh the drawbacks (blade-grind, hot-spots).
How?!

Did you ask if it'll be available everywhere?

-
@Mechanickal said:
How?!
Did you ask if it'll be available everywhere?

Magic...
ordered it from Singapore (shipping rate was reasonable and it was here lightning fast)... a well traveled knife

-
@Etherealicer said:
Magic...ordered it from Singapore (shipping rate was reasonable and it was here lightning fast)... a well traveled knife

[emoji38]
That was fast indeed...
Here's me hoping ...
-
Not fitting the sheath well.
The last one shows the deformation of the sheath without the tool inside!


-
you'd think they would have done a cut out or redesign to accommodate the different shape?

-
The OD Green "rubberized Cordura" sheath would've been perfect, but they go with the stiff regular sheath. It makes no sense to me. That's an off-the-shelf-solution to the tightness, as the OD green sheath has more "give", is capable of horizontal/vertical belt carry, MOLLE, and whatever else you need to strap it to.
-
@cody6268 said:
The OD Green "rubberized Cordura" sheath would've been perfect, but they go with the stiff regular sheath. It makes no sense to me. That's an off-the-shelf-solution to the tightness, as the OD green sheath has more "give", is capable of horizontal/vertical belt carry, MOLLE, and whatever else you need to strap it to.I prefer the sheath they picked, it feels way more sturdy as the green MOLLE sheath, and judging from the pics I think it will change shape a bit after a while and handle the OHO thingy's without any problem.
The Lock on my Victorinox S54 also pokes in the side of the sheath I got for it (same material as the one above), and after a while it fits much better.
I mean, it could be worse... My Leatherman OHT with the small Leatherman MOLLE sheath comes to mind...
-
@cody6268 said:
The OD Green "rubberized Cordura" sheath would've been perfect, but they go with the stiff regular sheath. It makes no sense to me. That's an off-the-shelf-solution to the tightness, as the OD green sheath has more "give", is capable of horizontal/vertical belt carry, MOLLE, and whatever else you need to strap it to.I think they use that sheath for the black oxide version.
https://www.military.sg/shop/home/2133-victorinox-swiss-tool-spirit-mxbs-australian-army.htm
I hope to be able to confirm in a few days, it is on its way. -
Yes, the BO version uses the OD green sheath.
-
Have to say I like it a lot, my solution for the wings


-
Agree. Mine arrived today.

(The black is consistent, the difference in the pic is just shadowsBeing left-handed, I was curious to see how the tabs worked for LH OHO. The serrated belt cutter opens with the thumb easily in the LH. To open the PE blade LH, I need to use my finger reaching around the Spirit to start opening and then adjust grip to finish opening, similar to LH opening of both blades on Wave.
Mine probably won’t spend much time in the case, because it will more often be in my organizer which it fits nicely.

-
Something else I find strange besides the blade grind, which I can fix is the fact they shortened the main blade by a few millimeters (2.5”/6.2 cm) compared to the S, RT, or XBS (2.7”/6.8 cm).
-
It must be a new blade blank that they stamp for the stud, so probably this has resulted in a small difference on the blade length.
-
The tabs presumably make it easier to find the main blade... on the normal Spirit I usually pull at the metal file and the saw before eventually finding the blade I'm looking for... all that symmetry is too much for a simpleton like me.
-
@pa_strunk said:
Something else I find strange besides the blade grind, which I can fix is the fact they shortened the main blade by a few millimeters (2.5”/6.2 cm) compared to the S, RT, or XBS (2.7”/6.8 cm).Probably because when using the thumb stud you're now pressing the blade to the middle of the tool a bit when opening. That could cause the blade tip to get caught onto the "pliers spring".
-
This would be ideal for the Dutch army, combing the functions of their DAK (OHO blade and belt cutter) with the issue Spirit’s tools.
Could also be useful for the Swiss Army but with the saw blade reinstated.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
