Wave & Rebar mod
-
Great job. I just wanted to ask how did you manage to add the scissors on the rebar frame without grinding it. I tried the same but no way to snap close the tool and it was no way for me to grind the scissors because i prefer it the way it is.Anyway if i dont find a way to add it like it is maybe i grind it but not before i am 100% sure about it. Anyway it is a great job you did there if you ever have the time to explain how i am waiting for an answer. Have a nice day and good moddings :)
-
@mastoras said:
Great job. I just wanted to ask how did you manage to add the scissors on the rebar frame without grinding it. I tried the same but no way to snap close the tool and it was no way for me to grind the scissors because i prefer it the way it is.Anyway if i dont find a way to add it like it is maybe i grind it but not before i am 100% sure about it. Anyway it is a great job you did there if you ever have the time to explain how i am waiting for an answer. Have a nice day and good moddings :)Adding scissors on this mod was easier cause i removed phillips, you need to re-organize tools to fit scissors without problems.
Try add scissors between blade and file, change large flathead and medium flathead with each other so scissors handle wont get gaught on medium flathead. So tool order should be blade, medium flathead, awl, large flathead, scissors and file.
If you take lanyard loop away you can put can opener there and then change phillips next to serrated blade and add scissors between phillips and saw.
I noticed that there is differences between tools, other may fit much more easily scissors than other.
Only Tools Matters
-
Thanks a lot Antti. I will start this tomorrow. I will be really happy for not grinding scissors. Cheers

-
Is the rebar held together with rivets, rather than screws?
If so whats your tips for dealing with these when modfing.
Thanks
Sent from my SM-G960F using Tapatalk
-
Not Rivets , they are proprietary bolts

You can get a special tool for disassembly from our own member loki-mobile
/topic/61708
-
The loki wrenches are totally worth the money
Makes modding many different LM MTs so much easy 
-
Oksy today tinkered again my Wave, now removed SE blade and added Wingman scissors. Changed Rebar pliers to it and added both bitdrivers back.
I shall call this LiteSurge


Only Tools Matters
-
I
it, Antti

-
Okey tinkered Wave again, now removed scissors and small bitdriver. Added Waves scissors back also SE blade was installed. Reason i removed Wingman scissors away cause theose scissors are bad and i really mean it, couldnt cut even paper properly.

Only Tools Matters
-
Necroing this again, now Wave and Rebar got new tools again cause last configuration didnt feel right. I may need mod Wave one more time (still feels little off)
Now Wave have all regular outside tools, gen 2 pliers (orginals)
Inside tools: modded can opener, Rebar phillips, Rebar Awl, microbit driver, large flathead.

Rebar tools
Orginal saw, File, Serrated Blade, PE Blade, Phillips and small flathead.
Waves Large Bitdriver, Scissors.
And as new tool hacksaw.
Changed screw for hacksaw side to Gerber MP800 (same pivot size but bit longer) added first lanyard but it wasnt ideal so i removed it (it made tools tight or loose when spinning and that wasnt ideal)


Modding hacksaw was quite simple, hardest part was getting pivot right size. Leatherman pivot size is roughly 4.7mm and i only had 4,5mm and 5mm drills so i needed to drill 4.5mm hole and then just file rest until it was right size. Next what needed to do was make locking notch to hacksaw, i did it with PST2 and metalfile when lock notch was ready need to round it like other tools (tried without doing that and opening was problem). After rounding hacksaw also noticed that i need bit also file/sand saw side otherwise it get stuck to bottom since it layed too low.
Also it was first sided with file but it was annoyingly hard to lift there since it has no nailnick so i changed side of Serrated blade and now lifting is easy and it still doesnt interfier with pliers. Also changed flathead and phillips place.


Hacksaw may see bit modding mainly cosmetic mod but nothing else.
I may try mod my ST300 too but bit bigger and better hacksaw (heavy duty)
Only Tools Matters
-
More great modding, Antti

-
Today modded again my Rebar, removed scissors and Bitdriver, replaced them with Wingman flathead and phillips (phillips only cause didnt know what to fill gap, but it jas been useful so far) main reason to changebwimgman flathead was that i wanted prying tool. Wingman flathead can actually handle much more prying than orginal.


Only Tools Matters
-
Good looking mod there, Antti. The Wingman flat point is a really stout tool. The edges are fairly sharp, so it makes a pretty good scraper as well. I hope your construction situation is coming along for you. Best wishes. Gary

-
Since i modded Rebar saw to my Center Drive (parts are now heading to Barry) my modded Rebar was missing saw.
Because that i decided to mod my own saw to it, used Wurth Heavy Duty Foxtail saw blade for base of my mod.From one blade you can make 2 saw, drawed lines to it and started grinding material away and the drilled hole to it to. Decided after first saw that i need bit better tools than dremel and drill. It was awful job to grind with dremel, next time i will need to lend grinder to get bit better result.
Saw is rough looking but it can now saw metal and wood. It wiggles bit since i made accidentally too large lock notch (next time need to be careful not to enlarge it too much)
Now my modded Rebar has
- Heavy Duty Saw
- Wingman Large Flathead
- Awl
- Wingman Phillips
- PE Blade
- SE Blade
- Metal Saw
- Rebar Phillips
- Rebar Small Flathead
- Wood/Metal File
- Rebar Pliers with Replaceable Cutters
I would say that now it can handle most jobs i can imagine (for scissors i carry Pioneer X) and since i have removeable Bit Driver i csn use flatbits and regular 1/4" bits.


Only Tools Matters

-
Awesome idea to make a saw from that recip blade, Antti :o

-
@Poncho65 said:
Awesome idea to make a saw from that recip blade, Antti :o

Thank you Poncho. I discovered that i could try to make saw for Rebar, basicly just needed model and bit of patience to do it. I will try improve next version bit better fit and cleaner look for it. I tested saw for wood and it cutted it like charm, at work we use those blades to cut wood, nails, metal frames and etc...
Only Tools Matters
-
Well now that Poncho modded PST i was bited modbug and made hybrid model.
Wave handle with modded serrated blade (chisel head) , Vic scissors, medium flathead, awl and microbit driver.
Rebar handle, file from Rebar, Wingman flathead, phillips and custom heavy duty saw and Rebar pliers. I will call this abomination as WingReVe.I may need to make few adjustment for tools but since im on PST challenge i wont be using this so much before challenge ends, maybe few testing.
[attach id=0 msg=2504331]

-
It's got an awesome toolset for sure 8) I had one similar to this for a while but ultimately I took it back apart and made a Wave and Rebar again
It worked very well but I just didn't carry it enough 
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login