Gerber Mr. Pinchy Multi Plier Club
-
Very nice, congrats !

-
Here is one of my Mr Pinchys that doesn't quite seem to fit into Hiraboo's chart.
It appears to be a BO version of sample 058 in chart.
Surface finishing: BO
Plier head: P-2
Nail mark position: Match
Handle cutout: Both Sides
Unique tool: Awl
Lanyard ring: Thin/Ground
Patenr Marking: M-2L
Font: solid (not outline)
Can opener claw: Parallel
Gap between handles: Pinchy. So very pinchy.
Joining methods: All button head screws.
Ruler: Inch both sides.


-
Oh man, these were my first multitool! I bought them when I was back in high school, but when I went to college and my cousin was going into the marines I gave him this tool for doing so and bought the newer locking one for myself, what a joke, I ended up braking like three of the tools doing such simple stuff, I think I just switched to leatherman, idk what I did with the tool

JR -
scrounger
Thank you for using the charts I made. And thank you new information.
I admit you have a unique tool I don't know. w(゚ロ゚)w
Wonderful!
I have to revise the chart. ヽ(^Д^)ノMadPlumbarian
Thank you for your wonderful memories. ٩(^ᴗ^)۶
The tools helped you in tough situation. And it would also have helped your cousin. -
MadPlumbarian
Thank you for your wonderful memories. ٩(^ᴗ^)۶
The tools helped you in tough situation. And it would also have helped your cousin.You want a good memory! I was on my way to the doctors, a good hour drive, and I was on the highway and stuck behind some truck, I decided to pass him so I drifted over to the next lane tapped the gas and went a little faster, I passed him then drifted back into the lane and took my foot off the gas, only thing was I didn’t slow down
so I figured maybe if I tap the gas peddle it would loosen? Bad idea, it stuck even further, next thing you know I’m really cruising, passing vehicle after vehicle, I didn’t know what to do? I was only a teen, I reached my foot under the pedal, and pulled up, notta, like crap,, here’s my exit, so I’m flying get off, and am coming up to a stop sign and I have both feet on the brake, the engine is going nuts, I let off the brake and the truck takes off, I come up to another stop sign and this lady is being an idiot, come on let’s go, TURN!! so she does and let off the brake and take off, and finally make it to my doctors office, slapped it into neutral and cut the truck off, I rolled in and found a parking spot put it in park, the hearts going, I look up and steam is just blowing between the hood and fenders, I go to pop the hood yet it was so hot, I found a rag to cover my hand and as I opened it, it was like a freaking cloud! Like OMG! So I drop the hood go to my appointment, which was forever, and the engine was cooled down, popped the hood look around, and notice the spring on the carburetor was broken and wasn’t pulling it back!
Now, the fun part I have no tools only my original gerber, but what do I do?
What would MacGyver do? So I look around and found a clicky pen, unscrewed it, took the spring out, rigged it to fit so I could make it to my grandfathers so he could get a better spring on it! Needless to say that one had so much tension on it, only problem a week later the throttle cable frayed and I ended up having to replace that!
JR -
Somehow I can't see that I've posted in this club before.

Big awl Multiplier for me. 8)

-
SteveC
An old and tasteful knives and the Mr. Pinchy.

MadPlumbarian
My heart have beaten as if i saw the movie "SPEED". p(> <)q
But I'm little surprised that the EDC tool saved you was a clicky pen, not a multi-tool! (´∀`)Gareth
What a cool pics!

-
-
@ReamerPunch said:
I want one!
PM me with some details of what you want, I might be able to help you out - I have some that I might let go (well, dozens actually).
-
@gregozedobe said:
PM me with some details of what you want, I might be able to help you out - I have some that I might let go (well, dozens actually).:ahhh

-
Could an MTO wizard please post a link to the post that lists all the different versions of MrPinchy?

-
@ReamerPunch said:
Could an MTO wizard please post a link to the post that lists all the different versions of MrPinchy?
Your wish is my command:
/post/928733There is also a later Mr Pinchy badged as "FISKARS" (not "GERBER") that has the giant awl.
-

I saw the Fiskars one in Chako's episodes thread.
Why is the MP evolution not a sticky?

-
@ReamerPunch said:

I saw the Fiskars one in Chako's episodes thread.
Why is the MP evolution not a sticky?

Because it's in the middle of another thread .
-
It probably should be in this thread

@gregozedobe said:
I copied much of the following info from a earlier post on MTo (possibly by Bob ? ), with revisions and additions from looking at various Mr Pinchies (and some assumptions on my part). Naturally any errors/omissions are my fault. If anyone has any corrections and/or extra info please speak up (eg which versions were made with a BO finish). Sorry, I can't do photos. I hope this helps out all those interested in the development of gerber's (in)famous "Mr Pinchy".**EARLY GERBER MULTI-PLIERS ("Mr Pinchy") **
Gerber kept making small changes to their Multi-Plier throughout the 1990's, so we tend to see a lot of subtle variations. Some were stamped and sold with the Fiskars logo, and at least some of these had slightly different tool loads (Fiskars owned Gerber at that time). At some stage Gerber started making a BO finish available, as well as the much more common bead blasted SS finish. Here's a summary of the main steps along the way:
Version 1) The very first models had a high-polish finish, instead of the bead blast we've seen on Gerber tools since. It also had button-head screws in all four blade pivot points, and button head screws on the plier slides. Also note the pivot bushing between the plier jaws. A crude pair of scissors was included, and a VERY thick Lanyard clip. The very first run of Multi-Pliers were etched with “FIRST PRODUCTION RUN” (a.k.a. “FPR” ) on one handle.
V1.0 FPR
V1.1 One handle cut-out, mis-matched nail nicks (don’t line up with cut-outs)
V1.2 One handle cut-out, matched nail nicks
V1.2 Two handle cut-outs, matched nail nicksAll ? “PATENT PENDING”
Version 2) The second version went to the now-familiar bead blast finish. The scissors were replaced by a big triangular shaped awl. This version still has button head pivots, button head sliders, and the pivot bushing between the plier jaws. The pliers had slightly beefier jaws with a squarer shape, while the lanyard clip was slimmed to a more “normal” thickness.
V2.0 “PATENT PENDING”
V2.1 “U.S. PATENT NO 5142721”Version 3) This version wasn't much of a change really. They simply did away with the pivot bushing.
All ? “U.S. PATENT NO 5142721”
Version 4) Changes: On one side of each handle, the button head screw was replaced with a round nut, while a file replaced the large awl.
V4.0 “U.S. PATENT NO
5142721/5142844” NB The 5142844 # was possibly an error, as later versions all used 5212844.V4.1 “ U.S. 5142721
PATENT 5212844
PAT PEND”**Version 5) ** This introduced a new, even beefier shape to the blunt nose plier jaws, and needle nose jaws were offered for the first time as well. Gone were the button head slider screws, replaced by two different sizes of round-headed rivets.
All ? “U.S. 5142721
PATENT 5212844
PAT PEND”At this point Gerber stopped with the minor evolutions of the Multi-Plier (Mr Pinchy) and came out with a major overhaul. Called the Multi-Lock when it first hit the market, the new tool had all-locking blades, plastic sliding lock releases, unique blade-pivot screws, the now familiar little circlip spring steel slider clips, etc.
After a while this tool became the 600-series Multi-Plier (MP600), with all its many tool component and plier type configurations. The very first ones were also stamped "First Production Run" (FPR).
All ? “U.S. 5142721
PATENT 5212844
PAT PEND” NB This is stamped inside the handle, not externally as before (and in a very small font).This information was last updated by gregozedobe on 5 August 2014
-
Greg
Oh, if you're thinking of letting go of your valuable collection
, please give me the detailed information. I would like to put your collection on my chart.
(For the time being, please tell me about your V1 collection.)Please fill in the following items like <u>scrounger did before.</u>
[list type=decimal]
-
Surface finishing:
-
Plier head:
-
Nail mark position:
-
Handle cutout:
-
Unique tool:
-
Lanyard ring:
-
Patent Marking:
-
Font:
-
Can opener claw:
-
Gap between handles:
-
Joining methods:
-
Ruler:
Sorry to trouble you, but I would like to keep a record of your rare collection.

-
-
Greg
Oh, if you're thinking of letting go of your valuable collection
, please give me the detailed information. I would like to put your collection on my chart.
(For the time being, please tell me about your V1 collection.)Please fill in the following items like
[list type=decimal]
- Surface finishing:
- Plier head:
- Nail mark position:
- Handle cutout:
- Unique tool:
- Lanyard ring:
- Patent Marking:
- Font:
- Can opener claw:
- Gap between handles:
- Joining methods:
- Ruler:
Sorry to trouble you, but I would like to keep a record of your rare collection.

I'll have to think about that. It would be a lot of work as I have around forty v1.x Mr Pinchies. Maybe if I only documented one of each of the different variants (I have a lot of duplicates) ?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

