wave/rebar custom hybrid project (pic heavy)
-
@Sam Lim said:
I too like the smaller SE blade.
for the differences in resistance when opening the pliers, u can try putting in a slotted screwdriver between the pliers and handle and give it a few whack. That usually loosen up abit. A pst tools will fit in a modern one after cutting the locking notch, so u get some more space with the philips like u said. My outside tools are from a OG supertool. They do sit flushed with the handle. Great work! 
that's a cool tip about the ST's tools fitting in the new wave. it's neat that you were able to replace all the wave's outside tools with the super tool's cuz i love that they sit flush! so you were able to get them to lock up with the liner lock and with that stop on the backside? do you have any pictures or posts on here that show any of that process? i would love to see or read any write-ups you have.
i'm wondering if the super tool's knife is a bit weaker though because of its size and shape? and how did you add the little grabby nub onto the knife? i've seen other folks use those, what are they called?thanks sam, maybe i'll PM you for links to all your posts having to do with mods......... i wish forums let you curate "playlists" of your posts/topics.
-
@oscillationsions said:
that's a cool tip about the ST's tools fitting in the new wave. it's neat that you were able to replace all the wave's outside tools with the super tool's cuz i love that they sit flush! so you were able to get them to lock up with the liner lock and with that stop on the backside? do you have any pictures or posts on here that show any of that process? i would love to see or read any write-ups you have.
i'm wondering if the super tool's knife is a bit weaker though because of its size and shape? and how did you add the little grabby nub onto the knife? i've seen other folks use those, what are they called?thanks sam, maybe i'll PM you for links to all your posts having to do with mods......... i wish forums let you curate "playlists" of your posts/topics.
Here you can see the blades sitting flushed with the frame..

The thumb studs began life as a M2.5 screw and nut. They are milled down to size for use. I have tapered the "head" of the screw so it sits flush at the back of the knife and stays in place. Note the notch on the knife for the thumb stud. I simply have no means of drilling so this is how I attach all my thumb studs. I have not encounter any issues but I am not a heavy knife user and I do not twist or pry with my knife. Yes all these knifes lock up nice and tight. Thats the beauty of modding. You get to choose how your want your tools to be and adjust to your liking.


Have fun!!
-
Great mods, and lovely wharncliffe knife!


-
Great job on those thumb screws and getting those blades in that Wave, Sam

-
looks kinda funny. like when your cat gets shaved..
so yeah,
just used a dremel to get off most of the material and then a file for the final touches and to ensure a flat surface
new idea though- i'm thinking about trying to fit all the drivers into the wave handle because my previous idea of putting 2 mini blades next to the phillips won't work. buut this will take shortening both flats so they clear underneath the phillips head (unshaved cat head). like so:
so yeah this would take a significant amount of length off of those flat drivers. they'd still work perfectly fine, just wouldn't have as much reach. but i'm not anticipating this being an issue for me.. plus all the drivers fitting together on one handle is verry pleasing to me
sooo, i'm gonna do it! sorry thinking out loud, thanks for reading! -
Hope you are able to accomplish this without to much fuss


-
@oscillationsions said:
looks kinda funny. like when your cat gets shaved..
so yeah,
just used a dremel to get off most of the material and then a file for the final touches and to ensure a flat surface
new idea though- i'm thinking about trying to fit all the drivers into the wave handle because my previous idea of putting 2 mini blades next to the phillips won't work. buut this will take shortening both flats so they clear underneath the phillips head (unshaved cat head). like so:
so yeah this would take a significant amount of length off of those flat drivers. they'd still work perfectly fine, just wouldn't have as much reach. but i'm not anticipating this being an issue for me.. plus all the drivers fitting together on one handle is verry pleasing to me
sooo, i'm gonna do it! sorry thinking out loud, thanks for reading!I would be a bit worried about the strength of that Phillips. There is a reason LM designed it that way. I hope it holds up for you though as you did a nice job of slimming it.
-
@oscillationsions said:
looks kinda funny. like when your cat gets shaved..
so yeah,
just used a dremel to get off most of the material and then a file for the final touches and to ensure a flat surface
new idea though- i'm thinking about trying to fit all the drivers into the wave handle because my previous idea of putting 2 mini blades next to the phillips won't work. buut this will take shortening both flats so they clear underneath the phillips head (unshaved cat head). like so:
so yeah this would take a significant amount of length off of those flat drivers. they'd still work perfectly fine, just wouldn't have as much reach. but i'm not anticipating this being an issue for me.. plus all the drivers fitting together on one handle is verry pleasing to me
sooo, i'm gonna do it! sorry thinking out loud, thanks for reading!Good job there; reminds me of the PST/PSTII Phillips screwdriver...nice!

-
all the drivers tetris'd together on the wave side
fits perfect
- slimmed down the phillips as described in a previous post.
- took about 7mm off of the medium flat driver, reshaped with a dremel, and filed the bevels by sight.
- took ~2mm off of the large flat driver, hand filed the existing bevel to get the end right for flat..driver'ing. may need more filing, i got lazy er... excited to be done.
a shot of the slimmed down 3D phillips driver cleaned up:
diamond file from the wave >> rebar:
- traced the rebar file onto the wave file, cut down most of it with a dremel and a cutting disk, hand filed and sanded the rest.
- drilling the pivot hole was the most challenging part. small carbide bits in a drill gun worked eventually. then diamond bits to get it to a more perfect circle, then a 7/32 drill bit at the very end. or... what i'd planned to be the very end.. the pivot still wouldn't go through, couldn't understand why. so i shaved away at the hole a bit with a diamond bit on the dremel. i ate away too much, the file is a little loose. anyone got a wave file they'd trade for a rebar????.. :( lol
- a note: i didn't have any cooling oil so i didn't use any. worked just fine without color changing somehow. i did take breaks every once in a while.
- lastly, i filed the rebar handle itself so the diamond side doesn't get eaten away at. there was some rubbing before as the tool was slid in and out.
- to anyone reading this and planning to do this mod, i would recommend drilling the hole first before cutting away at the other parts, that way, if your hole steers slightly off course for whatever reason (since it's a difficult process, you may have many reasons this happens), you can re-trace the rest based on the position of the new pivot hole.
i did the other mini knife too
- again, from the rebar's full-sized knife blade. determined a shape and nail nub position based off the needs of the plier head as it slides into position when the tool closes. (and also based off of where the knife needed to sit in the rebar.) then cut it roughly to shape with a dremel cutting disk. filed and sanded.
- i only just hand ground the edge's tip with a file based off of feeling, which was fun to do, but it's not the prettiest thing because the blade actually gets thicker at the tip due to the pre-established primary bevel and the invasion of the new tip where it wasn't meant to be. i don't feel like the bevel work needed to fix this issue is in my skillset quite yet. but in any case, i see this blade being mostly used for things like processing plant material or whittling, so i'm okay with the knife the way it is. for now.. this may change and i may have to pick up some knife-making skills.
that's all for now folks. will update again when i do my last big mod, the outside accessible vix scissors.
-
a clarifying picture of the process behind the shortened tools:
*
* -
Good job !

-
Great job on the tools modifications; glad its coming out the way you want it to be. Kudos on a job well done!

-
Glad to hear it is coming along the way you want it
Thanks for the update

-
Late to the thread but great job and welcome to

-
Those tiny blades are cute.

-
@ReamerPunch said:
Those tiny blades are cute.
nicely done. I always have a thing for tiny knifes. -
@ReamerPunch said:
Those tiny blades are cute.
hehe thanks i was waiting for this comment. they're my favorite
-
okay my vix scissors are taking forEVER to come in the mail so i'm gonna do a lil' mini update in the meantime
torque torque baby?
added some 90˚ locking notches on both my phillips and large flat for increased torque on screws that need it. works great and has reeeeallly helped me out a few times :) just have to use my second hand to push downward to drive the phillips/flat into the screw head while i twist with my right hand. a lovely 7.5" reach for nice torque power
those two locking notches
the phillips notch was much better than the one i made in the flat driver. locks dead tight with no wiggle, slides out of lock nicely, and is perfectly 90˚. can't say the same for the flat haha, that was my trial run. glad i did it in that ordertwiddles thumbs until vix scissors come in................

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login