Let me see your homemade sheaths!
-
@Tinner said:
That stamp is cool.
I may have to steal your idea and try my hand at making my own.Believe it or not it wasn’t hard, well, if you have a Dremel/rotary tool,
The hard part was
1, finding a bolt, I had to run out to the freezing garage, I found one but it was all old and rusty, but I turned around and saw a box and there were 4 brand new one in it and I was like SCORE

2, then making the layout, cause it has to be backwards, so I drew it with a marker on a piece of paper, once I got the just right I circled it and flipped the paper over, thus giving me the backwards layout,,
3, and lastly and the most annoying, matching the symbol to the paper, you’d get close and go over to the mirror to check, and naa, and of course marker doesn’t come off so you scribble really good all over the metal then wipe it really fast it comes right off! So after about 30min of fiddling I got a good match that I was pleased with,,The rest is fun, get the tool out and just don’t hit the marker! After its deep enough clean it up and your set, your suppose to stick it in a oven thingy and get it blazing red then dump it in water to harden it but I’m not using this thing to stamp metal, just leather.. so no point..
JR -
Thanks for the hints. Mine should be easy to make as my initials are MW. Upside down, backwards, forwards, same same lol. As long as I don’t get too fancy. I’m sure I’ll still find a way to mess it up.
-
@Tinner said:
Thanks for the hints. Mine should be easy to make as my initials are MW. Upside down, backwards, forwards, same same lol. As long as I don’t get too fancy. I’m sure I’ll still find a way to mess it up.Well the nice thing with the bolt is if you screw up you can just file it flat and do it over, but only one or two times,, getting into the M or W you might be better off with a very small square file and just work the angles / \ / \ util you get the letters made, because a rotary tools going to be round, unless you use a disk and cut like a saw,, all depends on how you want to make it?
//
//
//\//
////? Or something like this, it all depends on what you got going on, if you need any help or ideas don’t hesitate!
JR
-
When I mark my tools at work for identification I use M , with all the legs touching
WI do like the overlapped version you drew though. What are you using to press it into the leather? Arbour press? I have one, but it is rather large, that I use for pressing out bearings and such on my ATV.
-
@Tinner said:
When I mark my tools at work for identification I use M , with all the legs touching
WI do like the overlapped version you drew though. What are you using to press it into the leather? Arbour press? I have one, but it is rather large, that I use for pressing out bearings and such on my ATV.
So something like this? To stamp the mark? I just hit the bolt with a hammer, or do you mean to make the sheath?
JR
-
@MadPlumbarian said:
So something like this? To stamp the mark? I just hit the bolt with a hammer, or do you mean to make the sheath?
JRYes, like that minus the horizontal line. Two diamonds side by side.
And yes, to stamp the mark. I have seen a few videos with guys putting their makers mark on leather products with a stamp in an arbour press. I just assumed that there was a requirement to hold pressure on the stamp for a bit to set the image. If whacking it with a hammer works, well, I am a pro at hitting stuff with hammers lol.
-
@Tinner said:
Yes, like that minus the horizontal line. Two diamonds side by side.And yes, to stamp the mark. I have seen a few videos with guys putting their makers mark on leather products with a stamp in an arbour press. I just assumed that there was a requirement to hold pressure on the stamp for a bit to set the image. If whacking it with a hammer works, well, I am a pro at hitting stuff with hammers lol.
Nope, leather needs to be a little damp, line it up as to where you want it and give it a good hit with a hammer! Your done,, if the stamp isn’t deep enough you gotta get the stamp back into its little grove and make sure you don’t double stamp it, but then just tap it again until you get the right depth, if you over strike it then well it’s going to be a little too deep.. I mean as far as a press the closest thing I’ve used are clamps, in order to make the sheath I posted I took two pieces of wood, made a cut to fit the knife, then put the leather over the knife and clamped the two pieces together stretching the leather out in order to fit the knife, then used the same setup to clamp the two pieces of leather when gluing, here’s a quick show of how,
JR
-
That is how I wet formed both the Victorinox sheaths in the above pictures. I screwed a piece of wood protruding off my bench so I could clamp the three closed sides. Wrapped the knife tightly with saran wrap and worked thleather into the profile of the knife with a piece of rounded off dowel.
I think I found the basis for my stamp. Should work nicely. Have a 7/8” bolt around somewhere but in the abyss that is my shop.

-
Yeah I tried forming and stretching leather a few times that way but I just never could do it, but getting a form and just stepping on it or clamping it down worked for me!
JR -
Looks like I need to correct myself after browsing the SAKwiki. What I though I had was a Forester, when in fact it is a Rucksack as it has the sidelock. Discountinued in 2016 and replaced with the Forester which is a liner lock.
-
@Tinner said:
Here’s another of my creations. Both the knife and sheath. The knife is made from O1 tool steel with a handle made from Cocobolo. Flat ground with a cold blue finish to give it the patina look. The sheath is made as a scout carry with a ferro rod incorperated. Right hand draw.
Both sheath and knife look great! -
Made these sheaths for my EDC knipex duo not long ago :
The diagonal cutter needs the little elastic band to keep the sheath on, the Cobra XS doesn't, thanks to it shape.
-
@m47mu74nt said:
Made these sheaths for my EDC knipex duo not long ago :
...Cool!

-
@m47mu74nt said:
Made these sheaths for my EDC knipex duo not long ago :
The diagonal cutter needs the little elastic band to keep the sheath on, the Cobra XS doesn't, thanks to it shape.

-
@m47mu74nt said:
Made these sheaths for my EDC knipex duo not long ago :
The diagonal cutter needs the little elastic band to keep the sheath on, the Cobra XS doesn't, thanks to it shape.Those look great, well done!

-
Excellent work and cool idea m47mu74nt

-
Thanks all :-)
Main goal was "not to destroy" my EDC handbag with pliers heads -
I have been looking at the Leatherman bit adaptor for my rebar for a long time but I think it's a bit expensive for what you get. I don't need bits with my MT that often and when I know I need it I just get a proper driver.. But then it's the time when I do need it.
Then I remember an old bacho branded MT that lives in my car and that I already have a bit adapter that fits most multitools I have. But I don't want to put that in my pocket unguarded.. So I made this last night when wife was away and the kids had their screentimeNice and snug fit with the bits I use the most. It does look a bit wonky when the bits are in but the lines was perfectly straight when I made it. Looks worse in the pics but it still does the job



Don't know why it came out sideways but that's alright, we can pretend I did it on purpose
[It's not failure if you learn something from it]
-
I
it. Great work Kotti 
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login