Mad Max Challenge
-
Day 7
Another day, a whole 'nother set of possibilities...
Gotta love those precise SAK pliers

-
@Simon_Templar said:
Day 7Another day, a whole 'nother set of possibilities...
Gotta love those precise SAK pliers
Nice pic Simon!

-
@Simon_Templar said:
Day 7Another day, a whole 'nother set of possibilities...
Gotta love those precise SAK pliers
What are we making here? -
<u>Day 7</u>

"Official World Scout Knife"Wouldn't that be funny if every scout is carrying a Giant?
-
Very nice!!

-
@Simon_Templar said:
Day 7Another day, a whole 'nother set of possibilities...
Gotta love those precise SAK pliers
And with those scales it's a double special!
-
DAY 7
Comparing the inline Phillips screwdrivers on the XLT and Tool Chest Plus
-
I love Wenger! That's a knife on my bucket list.
-
Thank you Vicman!
@comis said:
Good use! Your post peak my curiosity and I brought out my XLT to play--
My Electrician blade is sandwiched between the scissors and spatula, and the bit driver only after the spatula. And mag glass layer is all the way out next to the openers.
I am curious do our tools have different orientation of layers? And does this happen randomly or done on purpose? I am sure most tools/chassis I have seen always have the same orientation due to nail nicks and ease of use.
It’s funny that you say that because mine has the exact same config as yours in line with ulzhan said but you are correct the only reason I put the wire in the direction of the driver and magnifier is because in my experience with using cat 5 laying the wire on the pliers made it a bit more level and I used the bit driver to hold it in place, I’ll post a pic showing how I do it
But I do have the newer magnifying glass on mine which sticks up more than the old one which is why I lift that layer out ( only going by your picture I don’t have the old magnifier myself to determine that for sure)
@Simon_Templar said:
Interesting and good to know. Did those extensions affect the handling negatively?Thank you Simon! They just make the cable sit less flush that’s why I open them up I’ll try to post a better picture in attempt to show how I try to do it
-
Day 7
Stormtrooper standing guard.
-
@FolderBeholder said:
Day 7
Stormtrooper standing guard.

-
I think the Giant is standing guard over the Storm Trooper Lisa!! :D
@FolderBeholder said:
Day 7
Stormtrooper standing guard. -
Does your Giant have the Evo scales?
-
This was definitely a learning process

So the first picture shows the large blade out without having to lift the bit driver, the reason this doesn’t work for me is because if I leave the large blade down the cable doesn’t sit flush on the layers of the tool and with it open is obviously a cutting/stabbing risk
The second picture shows how it works best for me I lift the magnifier out, then place the cable and partially close the blade on the cable then close the bit driver on the cable to hold it in place
Once it is in place the third picture shows how it works me to hold it I place it in my hand like that and rotate the bottom of the tool away from me holding the other end of the wire with my right hand (the pic is after I stripped it but wanted to show that part of the process)
In a pinch it does work well without causing damage to the inner cables but obviously if I was doing this regularly I would want the appropriate tools but as always the XLT comes through!
Comis, hopefully I made some sense with some of this




-
@FolderBeholder said:
Day 7
Stormtrooper standing guard.Great pic FB!

-
@FolderBeholder said:
Day 7
Stormtrooper standing guard.It's the other way around. No one wins against the Giant.
-
Day 07
A tale of two spatulas.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
Thanks Barry! :D