What is being carried today ?
-
Nice carry Juan


-

Your kit ain't too shabby either!
Oooh, and those two-part pivots on the Skeley...

And to think that they're now painted black with simulated pivot washers...

-
They have went cheaper on them

Nice, Steve 8)

-
@Juan el Boricua said:
May all @ MT.o are having a great Sunday!
For today, its Rebar and bit kit.What’s the bit kit for? I haven’t used the bit kit for my Rebar much, but I’m very glad it is an option. I just wish I could get a leather sheath that could hold the kit, a small flashlight and the tool itself. Leatherman has a black nylon sheath that can do this, but I don’t trust how it secures items on the sides. For the days I need one (aside from when I use my Surge for jobs around the house and it’s kit/tools), I bought an RAE sheath.
Sent from my iPhone using Tapatalk
-
Mostly for convenience, and "uncommon" bolt/screw heads, as it comes with various sizes of Torx, hex, two flat drivers, and Phillip's #0-3 (I've added a #1-2, this to protect the Rebar's as I'd rather buy bits than ship to have it fixed). Besides, it accepts regular bits, and I can replace from the 2-card bit kit to this one as needed; just in case. I needed a Torx for the hedge trimmer screws (may it RiP) and since the kit is always in the sheath, It's easier to grab it than go fetch one from the tool box.
And I hear you on the sheath; only options are custom made or DIY. I've had good luck with the newer nylon ones, at least miles-ahead better than the velcroed ones. I did modified mines by opening the top front seam, and use it as an extra pocket (where the kit is sitting in the picture) both on the regular and premium models. Hope all this rambling helps!
-
@Juan el Boricua said:
Mostly for convenience, and "uncommon" bolt/screw heads, as it comes with various sizes of Torx, hex, two flat drivers, and Phillip's #0-3 (I've added a #1-2, this to protect the Rebar's as I'd rather buy bits than ship to have it fixed). Besides, it accepts regular bits, and I can replace from the 2-card bit kit to this one as needed; just in case. I needed a Torx for the hedge trimmer screws (may it RiP) and since the kit is always in the sheath, It's easier to grab it than go fetch one from the tool box. Today, I needed the Torx for the hedge trimmer's (may it RiP) screws.
And I hear you on the sheath; only options are custom made or DIY. I've had good luck with the newer nylon ones, at least miles-ahead better than the velcroed ones. I did modified mines by opening the top front seam, and use it as an extra pocket (where the kit is sitting in the picture) both on the regular and premium models. Hope all this rambling helps!
The rambling does help. I’m glad I started this thread, as I’ve learned a few things such as how to pick out the lettering on a tool, sheath modifications, etc. I did order an RAE sheath, a new bit kit and extender to keep in the car. That’s at least what I’m telling myself.
As for the Charge+ I should have on the way, the tools aren’t for it, but my Surge, or Wave+, or whatever tool I may need them with for that day. Sadly, that’s not much or very often. When I used to do technical support for garage door openers, I would actually get to use my tools a lot, as it would help to break down the same or similar model of unit while troubleshooting. I would never do that job again as the management was abysmal.
-
@StrangeToolbot said:
The rambling does help. I’m glad I started this thread, as I’ve learned a few things such as how to pick out the lettering on a tool, sheath modifications, etc. I did order an RAE sheath, a new bit kit and extender** to keep in the car**. That’s at least what I’m telling myself.As for the Charge+ I should have on the way,** the tools aren’t for it**, but my Surge, or Wave+, or whatever tool I may need them with for that day. Sadly, that’s not much or very often. When I used to do technical support for garage door openers, I would actually get to use my tools a lot, as it would help to break down the same or similar model of unit while troubleshooting. I would never do that job again as the management was abysmal.
That reminded "my way of thought", and as of today, I have a bit kit with the Wave (carry the 2- bit cards kit; no need for an adapter), one with the BO Rebar and one with the Coyote, another with the Knifeless, and another one with the Super Tool 300; also with the Bladeless MP600 and my first BO MP600!!! So, yeah, I'm a big fan of it and its practicality!

(Aaand, I always find something to tinker with at home or at work, just to use them
)

-
Great looking carries, people!

-
Thanks Juan

-
Wave and Zebra for today.

-
Awesome carry, Juan 8)

-
Charge + in BO today


-
Nice carries Juan and Poncho

-
Thanks Steve

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


