Interesting LM post
-
@Dunc said:
I've just read a thread on Britishblades regarding LM Torx bits to fit an old style Wave . Nothing strange about that but its the comments made in post 4 that got my attentionCheers too Richard, I'd already tried the UK supplier route - but it never came through them so it isn't UK specification (UK ones had slightly different fittings so I have been told on good authority)
Link to full thread http://www.britishblades.com/forums/showthread.php?t=82595
Dunc
Whitby did my original LM Wave that I bought from the US without any problems.
-
I've just read a thread on Britishblades regarding LM Torx bits to fit an old style Wave . Nothing strange about that but its the comments made in post 4 that got my attention
Cheers too Richard, I'd already tried the UK supplier route - but it never came through them so it isn't UK specification (UK ones had slightly different fittings so I have been told on good authority)
Link to full thread http://www.britishblades.com/forums/showthread.php?t=82595
Dunc
Whitby did my original LM Wave that I bought from the US without any problems.
And I sent them a Charge for service that I got from the states

Dunc
-
Hmm, if you think about it, there's absolutely no reason the fittings should be different depending on which country they are headed to. The poster might have been referring to a difference in the various Torx that have been used; 5 pointed, six pointed security, six pointed standard...maybe he thought they varied by country

-
@Corrugated said:
Hmm, if you think about it, there's absolutely no reason the fittings should be different depending on which country they are headed to. The poster might have been referring to a difference in the various Torx that have been used; 5 pointed, six pointed security, six pointed standard...**maybe he thought they varied by country **
I'd say you are right. So far as I know there isn't any reason that there would be differences in the fittings depending on country.
-
Hmm, if you think about it, there's absolutely no reason the fittings should be different depending on which country they are headed to. The poster might have been referring to a difference in the various Torx that have been used; 5 pointed, six pointed security, six pointed standard...**maybe he thought they varied by country **

I'd say you are right. So far as I know there isn't any reason that there would be differences in the fittings depending on country.
Thats what I thought , I've even known people to have LM's that contain both 5 and 6 point screws

dunc
-
Thats what I thought , I've even known people to have LM's that contain both 5 and 6 point screws

I am one of them. Mine has 6 point security Torx at the plier ends, and 5 point security Torx near the locks.
Maybe the Americans don't know what to sell to the (French?) Canadians.
;)If it was done by country then shouldn't you have a Robertson screw head? :D
-
Thats what I thought , I've even known people to have LM's that contain both 5 and 6 point screws

I am one of them. Mine has 6 point security Torx at the plier ends, and 5 point security Torx near the locks.
My (new) Wave has 5 point on one side and 6 point on the other side, so I only need one of each to take it apart!
-
I thought the Canadian version did have Robertson bits in the bit kit.
-
They do, I remember jzmtl bought a Skeletool CX and it came with three bits: philips, flat, and robertson.
They are referring to the screws that hold the tool together...
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login