Car boot finds
-
Today’s $12 garage sale buy. Why yes! That is a Leatherman PST in the corner. Average price per tool $.20 US. :D
Three Nicholson 16 inch files, a Craftsman 4 once ball peen hammer., a Craftsman screwstarter screwdriver, a Proto screwstarter, a neat unbranded Phillips screwdriver with knurled handle, two Starrett wire gauges, and the PST.


-
Well that is just

-
Found yourself some good stuff!

Mike
-
Thank you Gentlemen.

-
Picked up a few goodies at an estate sale.




-
Estate sale buy. Craftsman v and vv wrenches, cockers and 1/2 ratchet. Thorsen 77 1/2 ratchet, with two sockets, an extension and two wrenches. S-K Wayne 1/2 ratchet, Proto wrench, Snap-on flex head wrench, a full set of Craftsman ball end metric hex wrenches, a 9-in-1 Craftsman SAE folding hex wrench set, a set of 10 Gedore Combination wrenches, and a Wheeler F.A.T. Torque wrench for guns.

-
Dang, you make out good!
JR -
I picked up these goodies at an estate sale today. Walden ratchet set, blue point and Bonney angle wrenches, a Craftsman 1071 plane, Starrett screwdriver and lots of other neat little pieces.There is also a great Miller’s Falls awl. A Lufkin 6 ft folding rule, a 3 inch made in Taiwan adjustable wrench, a set of Skil driver bits, a General Ratchet and few odd Craftsman extensions and sockets. Oh yeah, a small Lansky sharpening set. Well worth the $12.




-
Nice score! I swear you just keep finding all the goodies! Is the stick ruler an inside, outside or combo read?
JR -
What's the markings on the metal-handled tape measure? I have one that's a Western Auto brand, and it's close to 70 years old. I suspect someone else made it, however.
The Craftsman plane is the biggest score, however. I have a Lakeside (said to be Stanley) and it's in horrible shape.
-
@cody6268 said:
What's the markings on the metal-handled tape measure? I have one that's a Western Auto brand, and it's close to 70 years old. I suspect someone else made it, however.The Craftsman plane is the biggest score, however. I have a Lakeside (said to be Stanley) and it's in horrible shape.
Photo attached. No other marking except Made in U. S. A.

-
@MadPlumbarian said:
Nice score! I swear you just keep finding all the goodies! Is the stick ruler an inside, outside or combo read?
JRI have more to learn about folding rules. Both? Maybe? It has measurements on both sides and a brass depth gauge.




-
@Yadda said:
I have more to learn about folding rules. Both? Maybe? It has measurements on both sides and a brass depth gauge.Nope, an outside, the numbers start on the outside on both sides, some start only on the inside like mine which I can’t find, yet others will do both, it’s basically down to how you hold the ruler to measure, with an outside you’ll be holding, say if you just opened the first 6” the rest would but up to a table unlike an inside, the rest of the ruler would be above the table, if I can find my ruler I’d explain better but idk where it went to?
JR -
Ha ha, found it!
Ok, this is a both inside stick ruler, yours is a both outside with the brass slide, in some fields of work ones better then the other, I used to do ductwork and a inside was much easier because you didn’t have to have the ruler below the table in order to lay it flat, now they do also have combos, where one side is going to start on the inside like mine, yet flip it over and the other side is going to start on the outside, these are common but yours are probably the most common,,
JR


-
That is too cool. I was not aware of the difference. I have a half dozen of these and they are all probably outside. I will be checking them and watching for inside rules.
-
I must add on,
That’s why I love this forum, if you don’t know with what your dealing with whether it be a sak or some oddball item, either somebody does or somebody will do enough research to figure out something on it!
JR -
I agree. This is a special place.
BTW, I checked my rulers. All outside. I posted a pic and a list on the hand tool forum.
-
@MadPlumbarian said:
Ah, I figured you might have one with all the tools you find..
JRIt’s on the list. Now that I know they exist I will be looking for one.!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login