What did you use your Leatherman for today?
-
@GearedForwards said:
Nice use and nice locksport gear!I have some Sparrows sets, I need to get back into it, I haven't gotten past different rake/rock attacks yet

Thanks

If you are raking a lock you want to use bottom of the keyway tension and the tension you use should be very light otherwise you won’t be able to set the pins past the shear line
-
Rebar to open a delivery

/post/2245439

-
Is that the Universal Adapter
nice haul either way :o

-
@GearedForwards said:
Thanks for the tip, I need to get my locks out again

It is definitely a addictive hobby

-
-
:ahhh :ahhh :ahhhCongrats

-
Stroopwafels

-
One of my switch's pins got bent so I used my Juice's small pliers to bend it back straight

(Thanks again, Nix, for this LM!)

-
Good use, very fond of the Juice line, the S2 punches above its weight IMO, the CS4 has been my travel MT for many years

-
OHT against thorn [emoji1689][emoji41]
Sent from my SM-G960F using Tapatalk

-
Great uses guys

-
My Bond just got used harder than I have used pretty much every Leatherman. Normally I have a pair of 160mm Knipex combination (linesman's type with bolt gripping channel) in there along with a 8" pair because the smaller pair fits between staves; and the 8" gives me good leverage, but fits in tighter spaces than my full-on fence pliers. Well, today, Granddad and I were checking fences in the UTV, and noticed that a corner of the lower line fence had been pushed from underneath. The people that own that property bordering us are downright horrible when it comes to maintaining their fence lines. So, I had to push the fence in and affix two clips. I had the clips. But, somehow, I'd misplaced the smaller pair of Knipex pliers. The specialty tool I bought for post clips got one side of the first clip I used in, and then the other side would not go. Finally, I just had to bend that end with my Bond. Not my ST300; not my Surge (or even my better-for-fencing multitool the Swisstool). Took it surprisingly well. For jobs like these, I try to avoid using PST/Rebar/Bond sized tools. Rebar has done it before, however. I Just wish LM would go back to finer teeth on the pliers. These newer style teeth don't grip well; but they do wear better.
I'm going to find a bolt and drill a small hole in it; or perhaps find a hitch pin that will work (which I had). While the speciality tool works, it really only works about half the time. A lot of times, it either doesn't fit, or the clip is at an odd angle.
-
Skele helped install an very old CB radio into my very old motorhome today...


-
I used my Surge several times this weekend. Today I opened a couple packages of Spax screws with the serrated blade. I used the pliers to get out a few wood screws that did not properly seat into some plywood I am laying down to build up a subfloor. I used the saw to cut a small piece of ply to fit an area in a closet to help level before installing luxury vinyl planks. I used the bit exchanger and ratchet adaptor to dismantle an old office chair to fit in the trash.
So, what did you do today with the assistance if your LM?
-
Good stuff.

You might want to check out this thread: /topic/37474

-
Thanks! I searched threads and did not see this one. Can the mods merge them? Thanks!
-
I used the P-2 screw driver/large to put on new temp tags on new security patrol vehicle.
-
@MrToolJunkie said:
Thanks! I searched threads and did not see this one. Can the mods merge them? Thanks!Done

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

