Very stiff blades on old Explorer - looking for suggestions
-
@Huntsman said:
Great thread everybody
This is what this forum is all about - Helping each other out and sharing the love and knowedge

Great to see you getting so involved in the forum Sir SteveP

It's a real pleasure being here, Huntsman.
And I really do appreciate the knowledge that everyone has been so willing to share. I hope to be able to contribute as my knowledge builds.
-
@SteveP said:
Thanks, Rab21. Interesting info about WD40.The Explorer is working well at this point. The blades open fine, but don't "snap" closed like a new knife, though I haven't tried the clay that kamakiri suggested earlier in the thread.
I attached a couple of long-overdue photos...
My best guess is that it's from the mid to late '80s, so not bad shape for a 30+ year old SAK?
(I added the suspension clip, lanyard, and mini-screwdriver.)

Looks like 1986. I can’t see the bevel on the awl, but looks like it’s on the pivot end and not toward the tip. If it has the small ‘v’ on the tang, it is ‘86. Large ‘V’ and it’s late ‘86. If I’m wrong on the bevel on the awl, and it’s on the tip side of the eye, then it’s ‘87+. -
@kamakiri said:

Looks like 1986. I can’t see the bevel on the awl, but looks like it’s on the pivot end and not toward the tip. If it has the small ‘v’ on the tang, it is ‘86. Large ‘V’ and it’s late ‘86. If I’m wrong on the bevel on the awl, and it’s on the tip side of the eye, then it’s ‘87+.Small "v", so '86. You're good!
I'm not sure what I'm looking for with the bevel on the awl. Sounds like you've got the date locked down without it, but just for my knowledge?
-
I took a look at the liners using the 8x gray-rimmed magnifier on my Champion. Not a pretty site. The aluminum is pitted all over.
You poor knife. What did your previous owner do to you?
-
@SteveP said:
Small "v", so '86. You're good!I'm not sure what I'm looking for with the bevel on the awl. Sounds like you've got the date locked down without it, but just for my knowledge?
Thanks! And sorry I missed this post…
The ‘bevel’ is where the machined angles change. Earlier knives had the bevel close to the pivot end. Starting in ‘87, the bevel was moved to the tip side of the awl. So this is one of the easier timeframes to break up production annually.
Hope that explains clearly enough!
-
@kamakiri said:
Thanks! And sorry I missed this post…The ‘bevel’ is where the machined angles change. Earlier knives had the bevel close to the pivot end. Starting in ‘87, the bevel was moved to the tip side of the awl. So this is one of the easier timeframes to break up production annually.
Hope that explains clearly enough!
kamakiri, I finally got it with the bevel.
Between your description, this post with comparison pictures ( /post/1632103 ) in the topic "Something to help you date your Vic SAKS based on tool evolution", and comparing with a Deluxe Tinker I have from after 2005, I finally understand.
Mine has no bevel at all so MiniChamp's info dates it to 1985-86, aligning with your date of 1986.
As an additional confirmation, I found into on the different designs of the gray frame around the magnifier (same topic, reply 95 by Frater_Martin). Mine has beveled edges (compared to the right-edges on my 1983 Champion). Beveled edges seem to be from 1986 forward.
So everything points to 1986!
Thank you!
-
You’re welcome!
The magnifier actually changes by ‘84. My first knife has the beveled magnifier and was given to me that summer.
For at least the beginning of ‘85, there was no eye in the awl. And I believe got the 90° stop in the caplifter. I haven’t found any clear evidence of ones like yours in late ‘85, but possible.
-
If anyone is still following this saga...
I spent about 30 minutes vigorously bending the blades 90 degrees to the pivots, at multiple points from fully open to almost closed, bending out to the front of the SAK, to stretch the spacing. (Again, many thanks to Max Stone for the suggestion.)
Prior to this I had good "snap" when closing the two knife blades and the mag glass. The other tools needed to be pushed closed. (The reamer and corkscrew snapped closed great from the start.)
After the half hour of vigorous bending, I now have good "snap" when closing the Phillips and scissors as well.
The cap lifter and can opener have some "spring" when closing, I wouldn't call it "snap", but it's an improvement. There must still be some tightness in that layer because if I have open the cap lifter and can opener at the same time, then whichever I close first snaps soundly. I'm guessing the added tension of the open spring is overcoming the remaining tightness? But with just one tool open, back to the weaker "springy" close.
Personally, I still marvel at the change in this SAK from when I got it and needed a pry bar to open most of the blades. Now they all open easily and mostly close as if new. I'm a very happy guy!
And I hope all the tips shared in this topic help someone else down the road.
-
Good work, SteveP, and thanks for sharing your tips of what worked - I’ve been really lucky in that a soaking in warm water, detergent, a drop of WD40 and then a good wipe off with kitchen paper and then S drop of Victorinox oil have worked for me, but I’ve not had quite such a recalcitrant subject in front of me!

-
@Rizio Il Ghiro said:
Good work, SteveP, and thanks for sharing your tips of what worked - I’ve been really lucky in that a soaking in warm water, detergent, a drop of WD40 and then a good wipe off with kitchen paper and then S drop of Victorinox oil have worked for me, but I’ve not had quite such a recalcitrant subject in front of me!
Thanks, Rizio. That technique seems to be really useful for cleaning out dirt and grime. Lots of people here and on YouTube recommend it.
I think what's been the pain with this SAK has been the oxidized liners. I was shocked at the pits, small gaps, and roughness in them when I looked at them under a magnifying glass.
-
@SteveP said:
Personally, I still marvel at the change in this SAK from when I got it and needed a pry bar to open most of the blades. Now they all open easily and mostly close as if new. I'm a very happy guy!I'm awl-ways amazed at how an old, neglected SAK can be brought back to life with some TLC and elbow grease.
Never give up on a SAK!

-
@Nix said:
I'm awl-ways amazed at how an old, neglected SAK can be brought back to life with some TLC and elbow grease.Never give up on a SAK!

Good words, Nix.
I like this Explorer so much that it's become my daily carry at home, along with my Mini Champ. When I'm out, I switch up to my Swiss Champ and Mini Champ. But at home surrounded by a houseful of tools, the Explorer does what I need in a lightweight 91mm SAK.
It's like what they say about food you've grown yourself tasting better. There's just something special about a SAK you've brought back to life.
-
-
@comis said:
If all else fail(WD40, hot water bath with soap, etc), I would suggest to soak the knife into the white vinegar for couple of hours and see whether it will loosen the rust. I would try moving the joint every hour or so to see whether that would help the loosening. And toothbrush and flossing sometimes would help remove gunk too.^^^ This. The vinegar. Remove the scales and place it in a jar of vinegar overnight. Then rinse or blow it out and re- oil. I've removed stubborn rust off of second hand wrenches and sockets and such. In the case of solid tools ( no joints ) I left them in vinegar 2 to 3 days.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
