June Pocket Rocket Challenge
-
**Day 21
**
Mission: Tighten the hex screws holding together the Adirondack chairs on my deck.Equipment: Mini Champ with hex bit coupler on the combo tool. (The black strip to the left of the combo tool is a hard rubber shim.)
Disclaimer: I have to admit that the hex bit coupler moved to the inline Phillips on the Swiss Champ for final tightening. More torque than I felt comfortable putting on the Mini Champ.
Follow-up: This all got me thinking about portable hex bit capability. The hex bit coupler on the 58mm combo tool and the 91mm inline Phillips works pretty well. But a couple of the chair screws were close to other parts of chair, making it hard to get the SAK in, especially the wide Swiss Champ.
So inspiration struck and I used my Dremel to file down two edges on a hex key so it would slide snugly into the bit coupler without spinning. I did both ends of the hex key, so I've got length and torque. (See second photo.) Fits nicely into my pocket EDC kit, where I also keep the bit coupler and a few bits.
Disclaimer #2: For anyone trying this at home, my hex bit coupler is an odd-ball one I got with a Winchester multi-tool with a hex bit kit, though I've also seen the same kit with Gerber and no-name multi-tools. It's smaller than a standard 1/4 inch drive. A standard 1/4 inch drive-based coupler should do the job with a bigger shim and hex key.


-
@ElevenBlade said:
Day 21“What in the world is that?” You ask.
Its a raisin that I extracted from a packet with the help of the classic.
I was really hoping that it wasn't ear wax...

-
Day 21 late post.
Intense day, but with no uses for a SAK (a rare thing)
So, little Groot asked for a picture with minichamp
Enviado de meu moto g(6) usando o Tapatalk
-
@SteveP said:
**Day 21
**
Mission: Tighten the hex screws holding together the Adirondack chairs on my deck.Equipment: Mini Champ with hex bit coupler on the combo tool. (The black strip to the left of the combo tool is a hard rubber shim.)
Disclaimer: I have to admit that the hex bit coupler moved to the inline Phillips on the Swiss Champ for final tightening. More torque than I felt comfortable putting on the Mini Champ.
Follow-up: This all got me thinking about portable hex bit capability. The hex bit coupler on the 58mm combo tool and the 91mm inline Phillips works pretty well. But a couple of the chair screws were close to other parts of chair, making it hard to get the SAK in, especially the wide Swiss Champ.
So inspiration struck and I used my Dremel to file down two edges on a hex key so it would slide snugly into the bit coupler without spinning. I did both ends of the hex key, so I've got length and torque. (See second photo.) Fits nicely into my pocket EDC kit.
Disclaimer #2: For anyone trying this at home, my hex bit coupler is an odd-ball one I got with a Winchester multi-tool with a hex bit kit, though I've also seen the same kit with Gerber and no-name multi-tools. It's smaller than a standard 1/4 inch drive. A standard 1/4 inch drive-based coupler should do the job with a bigger shim and hex key.
Like that Hex key adaptation!

-
Day 21
Alox classic on duty today (I could understand how one could come down with the pox), cut down some antihistamines to throw in my booboo kit (I go through 2-3 'one a day' tablets per real life day, smurf you summer). It then supervised the ordering of some prime day Amazon goodies that will arrive tomorrow


-
Day 2
The Manager… managing…

-
DAY 22 A friend asked me to help do some flooring today, so I'm just anticipating what Skinny Mini can do today. Opening snacks will be vital, and I thought I might use the measure when we're cutting planks.


-
Now that's what it's all about!!@SteveP said:
**Day 21
**
Mission: Tighten the hex screws holding together the Adirondack chairs on my deck.Equipment: Mini Champ with hex bit coupler on the combo tool. (The black strip to the left of the combo tool is a hard rubber shim.)
Disclaimer: I have to admit that the hex bit coupler moved to the inline Phillips on the Swiss Champ for final tightening. More torque than I felt comfortable putting on the Mini Champ.
Follow-up: This all got me thinking about portable hex bit capability. The hex bit coupler on the 58mm combo tool and the 91mm inline Phillips works pretty well. But a couple of the chair screws were close to other parts of chair, making it hard to get the SAK in, especially the wide Swiss Champ.
So inspiration struck and I used my Dremel to file down two edges on a hex key so it would slide snugly into the bit coupler without spinning. I did both ends of the hex key, so I've got length and torque. (See second photo.) Fits nicely into my pocket EDC kit, where I also keep the bit coupler and a few bits.
Disclaimer #2: For anyone trying this at home, my hex bit coupler is an odd-ball one I got with a Winchester multi-tool with a hex bit kit, though I've also seen the same kit with Gerber and no-name multi-tools. It's smaller than a standard 1/4 inch drive. A standard 1/4 inch drive-based coupler should do the job with a bigger shim and hex key.
-
Day 22: My first Classic, a Christmas gift in 1985. At the time, I had been carrying my Huntsman for a couple years, and was satisfied with it so I put this guy on my keychain for my '66 Beetle. A couple of months later, the Classic disappeared. Untold moves later, in 2017 I'm going through a box of Momentos and there it was! A new set of scales and voila! As you can see, it's a non SD version. Does anyone know when the SD was introduced?

-
Day 22
H.E. the Ambassador on post opening duty this morning, scissors making light work of the bio-degradable plastic wrapping.

-
@Barry Rowland said:
Day 22: My first Classic, a Christmas gift in 1985. At the time, I had been carrying my Huntsman for a couple years, and was satisfied with it so I put this guy on my keychain for my '66 Beetle. A couple of months later, the Classic disappeared. Untold moves later, in 2017 I'm going through a box of Momentos and there it was! A new set of scales and voila! As you can see, it's a non SD version. Does anyone know when the SD was introduced?Pretty cool, Barry.

I don't think I have a non-SD tip Classic anymore.
-
@Barry Rowland said:
Day 22: My first Classic, a Christmas gift in 1985. At the time, I had been carrying my Huntsman for a couple years, and was satisfied with it so I put this guy on my keychain for my '66 Beetle. A couple of months later, the Classic disappeared. Untold moves later, in 2017 I'm going through a box of Momentos and there it was! A new set of scales and voila! As you can see, it's a non SD version. Does anyone know when the SD was introduced?And looking none the worse for being mislaid either Barry

-
Day 22. Some post duty for the Red Executive. Rather than show you the envelope here are the aviation cards I ordered.
Comedy Bonus pic: A Spork CD. Nope, deadly serious ... it's in my collection and I quite like it.


-
Day 22

-
Only one I ever had Nix. Phil, love those pics! Have you ever read The Shepherd by Frederick Forsyth?
-
Day 22
Free42 on iPhone - Free on the App Store.

-
Mrs. R's complete EDC kit. The only thing that I could give her was that No. 6! She won't take anything else. The 6 is for the rare occasion that the Classic won't quite do the trick. In addition to that well used Vic and Opinel, there's the Husky keychain tool and a Tractor Supply flashlight. She's never needed anything more, and I'm finding that to be true for me as well. Everything else is just for fun!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login