Best Multitool for IT technician
-
I have a CT-41 (CT-L) and a Swiss Champ. They are the same size. I can carry either one comfortably as long as I have a pouch or a pocket dangler so it's not sitting like a brick in the bottom of my pocket. The only thing I miss from the Swiss Champ when I'm carrying the CT-41 is the magnifying lens. I highly recommend the CT-M or CT-L. Any multitool can do a lot of jobs for you and can be combined with other multitools or dedicated tools for specific jobs where they might be needed. I like to carry my CT-41 with a Leatherman Crunch because they're very light and the locking pliers act as a third hand if you need them.

-
I carry a Swisschamp XLT and a Free P4/Charge TTI/Swisstool Spirit X everyday. I will also occasionally carry a Centerdrive if I think the situation calls for it. In my general-purpose tool bag, I have a 2nd-gen Surge, a Crunch, an E4, and a Vic Workchamp. In my wiring bag, I have a 1st-gen Surge. I have all of the Paladin/SOG line as well, but they are mostly retired and only come out for special occasions now.
-
Looking specifically for a multitool I'd suggest the Leatherman Wave personally, I carried it for a few years working 1st-3rd line.
My personal carry was in the leather pouch with side tubes:
-Wave
-Bit extender/adapter
-Bit card with most commonly used bits
-AAA flashlight
I carried a Cadet for more scared folks and had an iFixit tool kit for more involved work. A multitool will never replace your toolkit if you work on hardware or do infrastructure installations, but a good one will get you through most days without digging your kit out.
-
Cybertool L would be best.
-
+1 for Cybertool M/Cybertool 34 for the day-to-day.
I also like to have a Swiss Spirit with L-wrench bit kit in my pack.
-
Surge is overkill for IT work if you ask me. Neither Leatherman Rebar nor Wave have hex or star wrenches. Vic Cybertool seems like it would be good. I dont know, I dont own one. Wave with bit extender may be good. I dont know, I dont own one.
Today I disassembled a 15 year old 3Com 10/100 switch with my Leatherman Rebar to extract the 2 Papst 40x20mm fans inside. The bearings were finally going and they were making grinding and whining sounds. Anyway, the star screws on the bottom? I just grasped them with the needle nose of my Rebar. That's not always possible but it was in this case.
Left the case half open and pointed a floor fan at it. The whole thing is going to have to be replaced anyway
-
@ThundahBeagle said:
Surge is overkill for IT work if you ask me. Neither Leatherman Rebar nor Wave have hex or star wrenches. Vic Cybertool seems like it would be good. I dont know, I dont own one. Wave with bit extender may be good. I dont know, I dont own one.Today I disassembled a 15 year old 3Com 10/100 switch with my Leatherman Rebar to extract the 2 Papst 40x20mm fans inside. The bearings were finally going and they were making grinding and whining sounds. Anyway, the star screws on the bottom? I just grasped them with the needle nose of my Rebar. That's not always possible but it was in this case.
Left the case half open and pointed a floor fan at it. The whole thing is going to have to be replaced anyway
Torx bits (which is what I think you mean by star?) are included in the bit kit, I've used them on my Wave on occasion when I worked in IT.
-
@Explorer said:
This one looks perfect for what you’re describing. But does Anyone own or have experience with the Cyber Tool L? I do not.
This one seems to have replaced the Cyber Tool 41 (I could be wrong tho)
i’m not sure when it came out.
It looks like a great toolset for the price but I wonder how it compares to the other cybertool models?
Thank you to anyone who can shed some light on this model
Would be nice if they removed the large blade, the saw and the file, and the corkscrew and other backside tools. I've never once needed a straight woodsaw in 11 years of IT work. I have needed a paddle bit or hole saw to make holes in old furniture or cabinets for cables to pass through, but that's beyond the scope of a little hand tool.
Removing some of that superfluous stuff could slim the tool down a little...A long Philips, a couple of precision screwdrivers, some choice hex/ star bits, plyers, scissors, wirecutters, small blade for opening boxes of Dell computers, and a punchdown tool is about all you need. Wish Vic or Leatherman would make a tool with just that stuff on it. Id buy like 5 of them. And...This is one of the few times I might agree that the hook, since it already exists anyway, may as well be a part of this tool. It might help in teasing out telecommunication wires. Or, anyone who has ever tried to swap out ethernet cables from a full switch stack and punch down block can tell you, a thin hand or maybe a hook could be of service.
-
@GearedForwards said:
Torx bits (which is what I think you mean by star?) are included in the bit kit, I've used them on my Wave on occasion when I worked in IT.Yes. Torx bits. Seems like the bit kit can come in handy. Wave and Surge can make use of thier tiny screwdrivers, but I still think the Surge is too much weight. I wont carry mine in my pocket, and its even a little heavy on the belt for someone who doesnt do a lot of hardware work.
Does the bit extender fit the Rebar?
-
The more I think about it, the more i can say that the Wave scissors are puny compared to the Surge Scissors. And you could use scissors for wire wraps or zip ties. Surge scissors would take the cake there.
If learherman could make a somewhat thin, longer screwdriver (one that's actually strong, unlike those in the Surge and Wave), to get into recessed Philips head screws.All those knives and saw and file, though...unnecessary for IT
-
@ThundahBeagle said:
Yes. Torx bits. Seems like the bit kit can come in handy. Wave and Surge can make use of thier tiny screwdrivers, but I still think the Surge is too much weight. I wont carry mine in my pocket, and its even a little heavy on the belt for someone who doesnt do a lot of hardware work.Does the bit extender fit the Rebar?
They make one that sits on the phillips and can take full sized and flat bits!
-
@ThundahBeagle said:
The more I think about it, the more i can say that the Wave scissors are puny compared to the Surge Scissors. And you could use scissors for wire wraps or zip ties. Surge scissors would take the cake there.
If learherman could make a somewhat thin, longer screwdriver (one that's actually strong, unlike those in the Surge and Wave), to get into recessed Philips head screws.All those knives and saw and file, though...unnecessary for IT
For the most part yes!
...I may have cut through muliple steel cable locks when people left or lost their laptop lock keys with my Wave....
-
@GearedForwards said:
They make one that sits on the phillips and can take full sized and flat bits!Might be something for me to look into, since I dont have a Wave, but I do have a Rebar and an OG Surge
-
@GearedForwards said:
For the most part yes!...I may have cut through muliple steel cable locks when people left or lost their laptop lock keys with my Wave....
I may have done that as well but with the Rebar. Or the Metal Saw from my old Vic Mountaineer
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login