Daredevil Challenge 2021
-
Day 6
Time to try the nail puller, worked well


-
@Nix said:
What about a wooden dowel and some fine sandpaper?I done this for some serrated knives or kukri-type knives with big recurves.
I start with....well...a dowel of the correct size...and then sharpen using 600, 1000, 2000 grit paper. Strop with compound rubbed right on the dowel.
You can get a fabulous edge this way.
Hint: don't cut into the paper with the edge. Draw the paper from spine to edge.

Great idea, Nix. Thank you.
Too bad I read it just after ordering a diamond sharpening rod.

-
-
Day 06
Yesterday's afternoon storm left us without power for a couple of hours which led to my needing to change the 8 D cell batteries in a Coleman florescent lantern. The old batteries were dated March of 2011 so I think I got my money's worth out of them. -
@ReamerPunch said:
I had to dig into my can opener thread for this. I remember it performing adequately.
Here's my post of it. It did alright. Not that comfortable, and not perfectly consistent tracing along the rim, but it was fine.
I used to think all lip on can are the same, apparently maybe this is not the case? I gave it my best, but the blade was very barely touching the can lid.@Alan K. said:
Day 05
I said yesterday that the combo edge blade needed a touchup and I did something I never do. I used the carbide blade eaters on my SOG keychain tool. Normally I would use my Spyderco Sharpmaker with ceramic rods or I would use Arkansas wet stones and I would really take my time and give it my attention, but the Gerber MP600 just has an industrial look and feel that makes me think it is made to be abused and eventually replaced, so who cares if you touch up the blade with a carbide pull through sharpener. Anyway, it is sharp now. I will use a diamond coated sharpening rod to get the serrated portion later.Good job!

A little surprised the chisel grounded serrated portion didn't get destroyed by the pull thru, they tend to be thinner and more delicate than usual PE.
@SurgeUk said:
I bought it over the counter on my high street so I doubt it has anything other than the standard blade
I got it just after it was released in the UK (2015 ish?) Did they ever change them

Here's another recent shot of it for your perusal (maybe it's just the angle of dangle
)Oh, this angle does look like ordinary drop point.

@Poncho65 said:
I don't believe I will have an aha moment :D I prefer plain edge over serrated (serrated blades definitely have their place with certain tasks though
) but a PE blade overall will be the most practical for me
A combo edge is (in most cases) the worst scenario for me
:DI know there are some better designs of the combo blade out there but I still prefer PE

I share the exact sentiment here.

Definitely should keep an eye out and sign up pretty soon.
@SurgeUk said:
Can't believe I missed this...Chilli
:ahhh :ahhh :ahhh@Poncho65 said:
I meant to comment on it but was commenting on something else then got sidetracked at work

Anyways

:D -
@Sos24 said:
Day 5 (for real not Day 4 labelled “Day 5”)Needed to take advantage of a mild day. The Minimaster helped cut some fatwood in the morning for coffee and then a Fast Fire Stick in the evening for popcorn


It also helped open a package with a new SAK, but no picture.
Nice uses! Your pix kinda reminded me of the Corporal's video on bacon popcorn...say you don't happen to have bacon in the popcorn, or do you?
:D
https://www.youtube.com/watch?v=bDSrrWT4FKI@Humayd A R Mahomedy said:
Day 5
20210805_212847 by Humayd a r Mahomedy, on Flickri tightened the battery clamp in my truck
Good use!

@Alan K. said:
Day 06
Yesterday's afternoon storm left us without power for a couple of hours which led to my needing to change the 8 D cell batteries in a Coleman florescent lantern. The old batteries were dated March of 2011 so I think I got my money's worth out of them.Totally, and it's nice they didn't leak after all these years!

-
<u>Day 6</u>

Little guy surely has a way to express himself without words, he demanded me to put the table soccer up immediately without any delay. Out come the Wetols to help with the assembly.
-
-
-
@GearedForwards said:
...Malted milk are better dunkers
How very dare you be disparaging about my Hobnob

-
-
-
@ReamerPunch said:
Day 6Finally, a function the Flik excels in. Got a bunch of napkins outdoors? Stick a Flik on top, and those bad boys are going nowhere.
A few contestants here can give the Flik a run for its money, though. :D
Nice to see a function you are happy with

-
-
@comis said:
Nice uses! Your pix kinda reminded me of the Corporal's video on bacon popcorn...say you don't happen to have bacon in the popcorn, or do you?
:D
https://www.youtube.com/watch?v=bDSrrWT4FKIGood use!

Totally, and it's nice they didn't leak after all these years!

Excellent uses 
-
-
Daredevil Day 6: I wanted to test the idea of the hex driver on the file. I tried it first on a wood screw in my old workbench. It felt like I was going to spring the tool, so I quit. However, no other screwdriver would turn that screw (phillips in Swiss+Tech, ratchet driver, or old Craftsman). I them tried the phillips in the tool, and the hex driver on the file on some lesser screws. Both worked well. Call it a win for the Swiss+Tech today.




-
Excellent finish of Day 5 8) and Day 6 looking just as good

-

@Fireman said:
Daredevil Day 6: I wanted to test the idea of the hex driver on the file. I tried it first on a wood screw in my old workbench. It felt like I was going to spring the tool, so I quit. However, no other screwdriver would turn that screw (phillips in Swiss+Tech, ratchet driver, or old Craftsman). I them tried the phillips in the tool, and the hex driver on the file on some lesser screws. Both worked well. Call it a win for the Swiss+Tech today.



That's an interesting finding, I won't have thought of that.

@Poncho65 said:
Excellent finish of Day 5 8) and Day 6 looking just as good


-
@Fireman said:
Daredevil Day 6: I wanted to test the idea of the hex driver on the file. I tried it first on a wood screw in my old workbench. It felt like I was going to spring the tool, so I quit. However, no other screwdriver would turn that screw (phillips in Swiss+Tech, ratchet driver, or old Craftsman). I them tried the phillips in the tool, and the hex driver on the file on some lesser screws. Both worked well. Call it a win for the Swiss+Tech today.



Are you just screwing with us

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
