Daredevil Challenge 2021
-
Day 10 of 30
One third the way through now :ahhh I sure miss carrying different (and better
) tools 
The can/bottle opener/screwdriver
I never usually have a need for anything but the small screwdriver on something like this
I may not get to test this tool out much if any ::) :D
The Gerber emblem in a close up on one of the handles


-
Daredevil Day 10: No usage today, so I took a glamour shot in the sun.

-
@Humayd A R Mahomedy said:
Day 10the start of the double digits already :o
20210810_092028 by Humayd a r Mahomedy, on Flickr
knife blade use,i opened a package
20210810_092923 by Humayd a r Mahomedy, on Flickr
20210810_092926 by Humayd a r Mahomedy, on Flickr
and used the fine flathead driver to open a couple zip ties on my holster. this was a quick fix during "riot week" [widespread riots and looting here a couple weeks ago] until i got replacement loops [the package i opened today]Good use and hope all's better there now :ahhh

-

Used Wetols for lunch, and it really is just a walk in the park for the tool. Maybe it's my own OCD, I still can't get use to having random patina on my blades, and for that reason, I mostly prefer stainless blade for food use so I don't have to deal with the patina afterwards.
Or is it CDO (the correct order)
:ahhh -
One third the way through now :ahhh I sure miss carrying different (and better
) tools 
The can/bottle opener/screwdriver
I never usually have a need for anything but the small screwdriver on something like this
I may not get to test this tool out much if any ::) :D
The Gerber emblem in a close up on one of the handles


Nice detail shot there Poncho 
-
@ReamerPunch said:
Day 10I needed a new hole in a belt I have not worn in a while. The can opener did a decent job making the hole. Much better at this than opening cans.

Well deserved use there RP

-
-
-
-
<u>DAY 10</u>
Once again your practical uses surpass my own feeble efforts
It would appear that the twisted knee (done at work a couple of weeks ago) is not getting any better ::)
The OHT opened a support/strap-on type thing (no lewd comments please; you know who you are
)
-
**Day 10
**
Food prep again today, making a sandwich for lunch.The knife blade did a fine job slicing tomato.
The scissors attempted in vain to cut the plastic bag for the cheese. I gave up with them after a couple of snips and switched to the very sharp knife blade.

-
Thanks Surge

-

I had to change out the electrical service for a house today. The TripSaver assisted with tightening the nut on this standoff strap.
-
Just checking in.
Looks like you guys are up to no good.

-
Day 10:
Took a photo when the work was in progress, but apparently it didn't take as it did not show up on my phone.
I had elastic "Lock Laces" in my shoes. I didn't learn to tie my shoes until I was 12, and found it to be tedious until relatively recently. The elastic laces were more hassle than help. They always fit weird, and the tips would often pop off of them. I found other pairs of shoes I liked better, and usually wore those instead. I already got rid of them in one pair of workboots, but replaced them in a pair of older running shoes today. Had to use the Swiza's awl and can opener to pry off the tip. Tried to save as much as I could for reuse later.

Used the remaining (the other one got lost about two years ago) tip and some the leftover shock cord to make a lanyard for my new CPM-20CV Spyderco Jester. I normally don't bother with (expensive) Spyderco models, and I never have an interest in the sprint runs. Cheap for a sprint run ($50-something shipped), check. High-end steel that should hold an edge for a year or more, check. Model that has not been produced as a regular model since 2005, check. The model I wanted for a long time, but figured I'd have to sell a kidney or firstborn offspring to afford, check. Thus, I could not pass on it. The Jester evolved into the Ladybug 3, which uses the handle that originated in the Jester. I like the blade shape much better than the stock Ladybug profile.

-
Day 11

-
That looks good!
-
Day 10
I really am enjoying the Gerber MP600 Pro-Scout. The last several days have truly been a treat. The tools aren't too small after all and I think they should stand up to years of heavy duty use. I had always wondered what ever happened to all my old beer cans after I recycled them and now I know.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

