Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Half Multiforce

Scheduled Pinned Locked Moved The Mod Squad
50 Posts 1 Posters 5.9k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Half Multiforce
Half Multiforce
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • PitCarver Offline
    PitCarver
    Posts: 3,025
    PitCarver Offline
    PitCarver
    wrote on last edited by
    #40 Quote Reply

      @Adam5 said:

      I used the saw blade to cut in a lot of recessed can lights this week because I like it better than my Klein drywall saw. However, that left the knife full of drywall dust and in a desperate need of cleaning.
      Also, the scissors spring has been sifting a bit when using the scissors, causing an annoying click. I think that I left out a washer the last time I reassembled it :oops:
      In addition to those things, the straight driver that resides between the scissors and can opener is of very little use. There is a straight driver on the reversible bit in the bit holder. When I first performed the mod I knew the driver was wasting space but I did not have a good idea of what to replace it with.

      For all of those reasons, I yet again disassembled the knife. I thoroughly cleaned it and then went to work on replacing the straight driver. There were three tools that came to mind that I could use: a prybar, an awl, and a chisel/gouge/scraper. Given it resides opposite of the bit holder in the handle in the middle slot, its replacement could be no more than 3/4" to 1" longer than the driver. That eliminated the pry bar. So, I chose to install an awl.

      I have my old Suspension laying around doing nothing, so I decided to rob something from it to make an awl. Unfortunately, the area around the pivot is too narrow to cut in a notch for the Multiforce tool lock. :rant:

      So, I started looking over my other MTs that I am willing to rob from at this time.
      :rant:
      Nothing with enough length and rigidity to make a good awl.

      Then I spied a poorly formed chisel/reamer on a Husky plumber's MT. On to option #3, the chisel/gouge/scraper.

      I sharpened the chisel cut on the end so that it would actually gouge out wood. I sharpened curved part of the tool so that it could actually remove burrs from PVC conduit. And I ground a chisel edge along the other edge of the tool. I forgot to take a close up pic of the tool, but it is visible in the picture above.

      In addition, I gave the scales another ferric chloride bath. The previous treatment was holding up well, but since I had it disassembled I figured I might as well do it.

      I was thinking about mine, last night. I had wanted to include the serrated blade instead of the saw, but the indent was on the wrong side. Then I thought that why can't I simply drill through the current indent creating a hole to actually act as an indent.

      Now, I'm almost ready for our vacation to end so I can get back to my tools.

      1 Reply Last reply
      • johnnyvol Offline
        johnnyvol
        Posts: 28
        johnnyvol Offline
        johnnyvol
        wrote on last edited by
        #41 Quote Reply

          I've taken this apart so many times due to putting something in backwards or leaving an important washer out that I believe I could assemble it blindfolded now. Zip ties are a great help also.

          Anywho, here's my half MF alongside the Gerber Armbar Drive and Slim Drive, a Rebar and an original Wave for size comparisons.

          MFGAD.jpg

          1 Reply Last reply
          • Poncho65 Offline
            Poncho65
            Global Moderators
            Posts: 88,523
            Poncho65 Offline
            Poncho65
            Global Moderators
            wrote on last edited by
            #42 Quote Reply

              I am pretty sure I would like this better than an Armbar :salute: Great comparison pic :cheers: :like:

              1 Reply Last reply
              • PitCarver Offline
                PitCarver
                Posts: 3,025
                PitCarver Offline
                PitCarver
                wrote on last edited by
                #43 Quote Reply

                  @johnnyvol said:
                  I've taken this apart so many times due to putting something in backwards or leaving an important washer out that I believe I could assemble it blindfolded now. Zip ties are a great help also.

                  Anywho, here's my half MF alongside the Gerber Armbar Drive and Slim Drive, a Rebar and an original Wave for size comparisons.

                  :like:

                  1 Reply Last reply
                  • PitCarver Offline
                    PitCarver
                    Posts: 3,025
                    PitCarver Offline
                    PitCarver
                    wrote on last edited by
                    #44 Quote Reply

                      Ordered me another Multiforce along with a couple other knives while we were on vacation because all the Walmarts were out. Got home today and found that they beat me here.
                      I love shipping like that.

                      Now I've gotta decide if I want to keep it as is or try another mod...

                      1 Reply Last reply
                      • Poncho65 Offline
                        Poncho65
                        Global Moderators
                        Posts: 88,523
                        Poncho65 Offline
                        Poncho65
                        Global Moderators
                        wrote on last edited by
                        #45 Quote Reply

                          :popcorn: :like:

                          1 Reply Last reply
                          • Adam5 Offline
                            Adam5
                            Posts: 8,411
                            Adam5 Offline
                            Adam5
                            wrote on last edited by
                            #46 Quote Reply

                              While reading some of the modding threads, I saw where J-sews and Evil both created additional bits that could be inserted in the Surge/Wave bit holder. That inspired me to to do something similar.

                              However, the Multiforce bit holder is for 1/4" bits, not the flattened Leatherman bits. And I happen to have a lot of those type of bits around. Also, I have access to a lot of worn out paddle drill bits that could be repurposed. So, I have made a few accessory tools for my knife in my own manner:

                              I made a small scraper, a large scraper, a prybar, a punch/marlin spike, and an awl.

                              In order to use these tools, I flipped ends with the bit holder so that it locks. Fortunately, the can opener and the scissors work just fine with the plier back spring without any modifications. The scraper I made that resides between those two tools is only partially functional now. I will have to rethink what should go there. Perhaps some holder for tweezers :think:

                              By the way, I inserted magnets in the Multiforce bit holder and the extension so that regular 1/4" bits will work in them. The Leatherman ratchet still works fine in the bit holder.

                              1 Reply Last reply
                              • Poncho65 Offline
                                Poncho65
                                Global Moderators
                                Posts: 88,523
                                Poncho65 Offline
                                Poncho65
                                Global Moderators
                                wrote on last edited by
                                #47 Quote Reply

                                  Just now seeing this :o that is an awesome idea with all those tools :tu: I remember seeing the things that J-sews (Bob) made out of spade drill bits and the tools you have made are equally awesome :salute: :like: :like:

                                  1 Reply Last reply
                                  • Adam5 Offline
                                    Adam5
                                    Posts: 8,411
                                    Adam5 Offline
                                    Adam5
                                    wrote on last edited by
                                    #48 Quote Reply

                                      Thanks!

                                      The awl has already been useful. I was helping repair a cabinet and needed to create a couple of pilot holes in a tight spot. I could not get a drill in there, but the awl fit. I was able create enough of a starter hole for each screw so that I could drive in the screws using the Multiforce knife.

                                      And I used the small scraper today to clear out some foam in a slot that I had to install a wire in.

                                      1 Reply Last reply
                                      • Poncho65 Offline
                                        Poncho65
                                        Global Moderators
                                        Posts: 88,523
                                        Poncho65 Offline
                                        Poncho65
                                        Global Moderators
                                        wrote on last edited by
                                        #49 Quote Reply

                                          Nice :salute: :like: :like:

                                          1 Reply Last reply

                                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                          With your input, this post could be even better 💗

                                          Register Login

                                          1. Home
                                          2. Tool Talk
                                          3. The Mod Squad
                                          4. Half Multiforce
                                          Reply
                                          • Reply as topic
                                          Log in to reply
                                          COMMUNITY LINKS
                                          EDC-TV SAKWiki GearFeed SAKSelector
                                          Operational Funds

                                          Help us keep the Unworkable working!

                                          Make A Donation
                                          November Goal: $300.00
                                          Due Date: Nov 30
                                          Total Receipts: $0.00
                                          Below Goal: $300.00
                                          0% funded
                                          • Login

                                          • Don't have an account? Register

                                          • Login or register to search.
                                          • First post
                                            Last post
                                          0