Daredevil Challenge 2021
-
Day 13
I had a piece of wire on my bowdrill, to keep the spindle in place, when getting into position. But it was a little loose and it bothered me. I removed it with the pliers, and put a screw in place. Nice and firm, no rattling, and I can remove it easily if I want to. The Phillips bit nicely into the screw and drove it with no issue, other than subpar ergonomics.

-
@ReamerPunch said:
Glad to see Coco is doing fine.
@Nix said:
Hoping Coco heals up soon! Awl-ways tough to see these guys suffer.Thanks very much awl

She's a bit better today, still needs supporting by her harness to move but has been lying out in the sun on the grass verge so she can at least get the doggie smells etc as well as lots of treats and attention

-
@ReamerPunch said:
Day 13I had a piece of wire on my bowdrill, to keep the spindle in place, when getting into position. But it was a little loose and it bothered me. I removed it with the pliers, and put a screw in place. Nice and firm, no rattling, and I can remove it easily if I want to. The Phillips bit nicely into the screw and drove it with no issue, other than subpar ergonomics.

Cool use RP

-
Day 13

-
Day12
The Minimaster helped with putting a split ring on a flashlight.

It then cut open a snack

-
-
Daredevil Day 13: Sunrise at the beach. 8)

-
Nice pic Fireman!
-
Day 13 of 30
Friday the 13th :ahhh
:ashley:
Still early in the day here but it's already hot and humid

No uses for the NXT yet and as hot as it is there may not be
thankfully not very busy at work right now 

-
Day 13
My grandson didn't have much good to say about the saw either. He wanted the Super Tool




-
Friday the 13th :ahhh
:ashley:
Still early in the day here but it's already hot and humid

No uses for the NXT yet and as hot as it is there may not be
thankfully not very busy at work right now 

Nic pic!
It's suppose to be a high of 97°F here in NC, but I don't have to work today

-
Thanks

Glad you don't have to be in it today
Great pics and
with your grandson about wanting the Supertool :D -
Day 13
20210813_141502 by Humayd a r Mahomedy, on Flickr
i got this SRK from a buddy who decided to pull off the handle and glue it back on with "sticks like smurf". he used a fastener in the lanyard hole.
this arrangement bugged me until i decided to use a tube to line the lanyard hole.
pictured is my 3rd or 4th attempt,i keep cracking the tube when i try to flare it.
20210813_141748 by Humayd a r Mahomedy, on Flickr
the Swisstool worked,i was a bit concerned about the "hybrid" pliers,but it did what was needed just fine.
20210813_142452 by Humayd a r Mahomedy, on Flickr
i used a thin-walled stainless tube,this side is passable.
20210813_142456 by Humayd a r Mahomedy, on Flickr
this side is fudged.
back to the drawing board
20210813_164545 by Humayd a r Mahomedy, on Flickr
i used the serrated blade to open a bag of cat food,it zipped through -
Day 13
Stuck in traffic earlier this morning, but now safely back home. -
@ReamerPunch said:
Day 13I had a piece of wire on my bowdrill, to keep the spindle in place, when getting into position. But it was a little loose and it bothered me. I removed it with the pliers, and put a screw in place. Nice and firm, no rattling, and I can remove it easily if I want to. The Phillips bit nicely into the screw and drove it with no issue, other than subpar ergonomics.

You lost me at "piece of wire" ::) (very good use
) -
@Alan K. said:
Day 13
Stuck in traffic earlier this morning, but now safely back home.Is it acceptable to whip out your tool and display it on the dash for awl to see

-
@Humayd A R Mahomedy said:
Day 13
20210813_141502 by Humayd a r Mahomedy, on Flickr
i got this SRK from a buddy who decided to pull off the handle and glue it back on with "sticks like smurf". he used a fastener in the lanyard hole.
this arrangement bugged me until i decided to use a tube to line the lanyard hole.
pictured is my 3rd or 4th attempt,i keep cracking the tube when i try to flare it.
20210813_141748 by Humayd a r Mahomedy, on Flickr
the Swisstool worked,i was a bit concerned about the "hybrid" pliers,but it did what was needed just fine.
20210813_142452 by Humayd a r Mahomedy, on Flickr
i used a thin-walled stainless tube,this side is passable.
20210813_142456 by Humayd a r Mahomedy, on Flickr
this side is fudged.
back to the drawing board
20210813_164545 by Humayd a r Mahomedy, on Flickr
i used the serrated blade to open a bag of cat food,it zipped through
I wouldn't even know where to start 
-
-
@cody6268 said:
Day 12; got into some stuff to start a computer repair kit. I own few decent screwdrivers, so I picked these up. I have seen this USA-made design under several different names over the years, but they are most associated with Klein. Same screwdrivers, just blue acetate and not yellow.
Nice 
-
No use at all today. :(
Went to an estate sale this morning, but no SAKs. Just some cheap Chinese multi-tools. (Too bad the sale wasn't last month. I would have been set for the challenge!) The house was a hoarder's house. It was...interesting.
Spent the afternoon watering the parched lawns. They aren't liking the near 100 degree temps. The S557 was no help with that.
So just a photo of the S557 posed with some other members of my collection. See if you can identify them!
That's a lot of tool... 
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
