Curl Owners Club
-
@GearedForwards said:
Huh, in the states if you have friends in lower tax states and they were amiable, could you pay via them as the billing info but still have it delivered to yourselves, saving a bit in the process?
It depends...
If the seller is shipping to a buyer in another state (one where they do not have a presence), they are not required to charge a sales tax. However, the buyer's state will likely require sales tax to be paid there. It's confusing.
-
Been carrying the Curl with its pocketclip hanging inside my front right pants pocket for the past day or two. My initial thoughts:-
POCKETABILITY
While not nearly as light as my Vic Compact or Skeletool CX, the Curl is 'acceptable' to me as an everyday carry. Probably near my maximum bulk tolerance as an EDC. By way of reference, I have a first gen Wave and Vic Spirit X, none of which I will carry as an EDC because of the bulk and weight. Both great toolsets though.
TOOLSET
Plain edge blade, pocketclip, scissors, bit exchanger, awl, what more do I want? If I can have the wood saw instead of diamond file it would be the perfect EDC toolset for me. Please Leatherman, can you fix that, maybe Curl version 2 (call it Curl S)?
QUALITY
Excellent. Much better than my old Wingman.
VERDICT
Pocketability is top priority for me as an EDC. The Curl delivers that, plus a more complete toolset that I use often. More than the Skeletool (+scissors) and the Vic Compact (+pliers), in an acceptable lightweight form factor that I can carry with me everyday. It will be my EDC going forward, for now. Until Leatherman gives me Curl S, with a saw !
-
I wonder if the saw from the Wingman/SideKick would fit ?
-
Ordered
and being delivered tomorrow! 
-
@gadgetman7 said:
I suspect a Wave saw would fit it and you can sometimes get them on EBay for around $20 US.Sent from my iPhone using Tapatalk
I'm sure the Wave saw will fit the Curl, since the Curl appears to have the standard Wave file, and the file and saw are interchangeable on the Wave; in fact, that's my plan if I end up buying a Curl at some point. I probably wouldn't be interested otherwise.
However, I highly doubt the Sidekick saw will fit. Assuming the blade pivots are the same diameter on the Curl as they are on the Wave, the pivot hole in the Sidekick saw is too small to fit onto the Wave/Curl pivot. I just tested it on my Wave and it doesn't fit.
-
-
The Curl is already showing "In stock soon" on Amazon.
-
Thanks for the ideas gents ! I have a first gen Wave and I am quite happy to swap over the saw to my Curl. As I haven't taken apart a full size LM multitool yet, any advice/ tips/ what to watchout for would be appreciated. More concerned how to put it back together, especially with the locking mechanism on one end and slip joint spring on the other.
-
@roamingcat said:
Thanks for the ideas gents ! I have a first gen Wave and I am quite happy to swap over the saw to my Curl. As I haven't taken apart a full size LM multitool yet, any advice/ tips/ what to watchout for would be appreciated. More concerned how to put it back together, especially with the locking mechanism on one end and slip joint spring on the other.If all you're doing is putting a saw in, I think you just need to yank the pivot out and make the tool swap. It should be as simple as maintaining any locking folding knife, just be aware that they use security bit Torx.
-
Assuming you already have a pair of Torx T10 security bits, make sure that you have some loc-tite.
You shouldn't have to take the whole Wave apart to remove the saw.
Removing the saw from a Wave is pretty easy, since the male half of the pivot screw threads into the saw side of pivot pin. So all you have to do is unscrew the pivot screw on the saw side and slide the saw off of the pivot. You shouldn't have to remove the entire pivot pin to take the saw off. Be sure to save the bronze washer that's between the saw and the frame.
Note: You might have to pull the whole pivot pin out to remove the saw, but it all depends on which side the pivot screw threads into. It works equally well either way, and I've dissembled and reassembled my Wave so many times that I'm not sure of the original orientation of the pivot.
Removing the file from the Curl is exactly the same (I'm assuming this, based on the visual similarity of the tools and their use of standard Wave parts).
-
Appreciate the advices gentlemen, thanks
. Sounds like a less daunting task then I first thought :). Thats my next project for the weekend. You all have a great weekend ahead! -
I cringe at the thought of replacing the file with a saw, but different strokes for different folks :)
Please post some pics when you're done.
-
Just ordered mine! $65.02 thanks to the coupon code from Poncho!
-
-
@roamingcat said:
Thanks for the ideas gents ! I have a first gen Wave and I am quite happy to swap over the saw to my Curl. As I haven't taken apart a full size LM multitool yet, any advice/ tips/ what to watchout for would be appreciated. More concerned how to put it back together, especially with the locking mechanism on one end and slip joint spring on the other.As already mentioned you don’t need to take it all apart, just the screw that holds the bit you want to take out. Did a video a while back taking apart my Surge, it will give you an idea what to expect. Nothing to be afraid of.
https://youtu.be/e2Mtq5y-KKMa -
D*mn you Poncho65!!

I've been such a good boy lately, but I can't pass up the curl at $65 shipped.

Also, I will never judge women for having 50 pairs of shoes we are all just as sick.
-
@DavisNikolov said:
As already mentioned you don’t need to take it all apart, just the screw that holds the bit you want to take out. Did a video a while back taking apart my Surge, it will give you an idea what to expect. Nothing to be afraid of.
https://youtu.be/e2Mtq5y-KKMaThank you.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

Really excited for the Curl!