Gerber Armbar Owners Club
-
Let me add to the chorus that the Armbar Drive could have been, but definitely is not, a great pocket MT

I will be using it in September during the SAK-alike challenge. Hopefully I will find that its positives outweigh its flaws.
-
@Adam5 said:
Let me add to the chorus that the Armbar Drive could have been, but definitely is not, a great pocket MT
I will be using it in September during the SAK-alike challenge. Hopefully I will find that its positives outweigh its flaws.
Me too. My thought is that the one-hand opening blade in this size (about the same as a 91mm SAK) will offer some advantages.
I opted for the Cut instead of the Cork because I don't open wine bottles all that often - and I use bits even less, I would think that a lever arm is a distinct advantage over the many MT corkscrews without one. Some reviews out there point toward a useful tip - the corkscrew is relatively short, so you have to pull the cork in two stages. Screw it in halfway so the lever arm engages, and pull. then screw it in the rest of the way to where the lever arm engages and pull again. Two pulls should get the job done.
-
I've had one of these for a couple of weeks now and I'm really starting to like it. It's a good size for pocket carry, not too heavy and the blade is a beast. Don't ask why, but I had to use it to pry the center caps off the front wheels of my truck and the blade was all I had at the time. Not even a nick. Just a couple of passes on the DC4 and sharp as before.
I did do one thing to help out with the lack of "snap" on the tools. I took the tool apart and bent the back spring down to give it more resistance and put it all back together. There is an audible pop when the tools engage now. It's still no SAK but it takes a little effort to disengage now.
I'd post a photo but something about this forum software has me stymied. Maybe I have to have more posts to upload pics?
EDIT: Photo added but I have no clue how, lol.

-
Welcome to
and good job on adding some tension to your Armbar

-
I'm starting to like the Armbar a lot more, and the locking mechanism a lot less. :ahhh
Does anyone else have an issue with disengaging the lock? I have to switch hands and depress the liner lock with my fingertip just to get it to unlock. My thumb can't get close enough to the tang where the lock meets it, so the liner lock doesn't back down from the blade (because pressing the middle of the lock all the way down results in the business end of the lock still sticking up against the tang). So I have to switch hands and get the tip of my index finger right up to the top of the liner lock and press it in,
I have small hands to begin with so I should easily be able to do this with my thumb, and can do so with all my other liner locking blades.

-
Been eyeing one of these, for a while now, now that johnnyvol has posted a make-do solution to the tool tension, I might just have to pick one up
Just a question for the slim owners, is the bit holder tension the same as the standard armbar?
-
@ElevenBlade said:
I'm starting to like the Armbar a lot more, and the locking mechanism a lot less. :ahhhDoes anyone else have an issue with disengaging the lock? I have to switch hands and depress the liner lock with my fingertip just to get it to unlock. My thumb can't get close enough to the tang where the lock meets it, so the liner lock doesn't back down from the blade (because pressing the middle of the lock all the way down results in the business end of the lock still sticking up against the tang). So I have to switch hands and get the tip of my index finger right up to the top of the liner lock and press it in,
I have small hands to begin with so I should easily be able to do this with my thumb, and can do so with all my other liner locking blades.

I kind of poke my thumb nail and push on the liner lock up next to the pivot. I have no problem doing it one handed but there is a definite point of release. You might try to just ever so lightly polish the liner lock where it meets the blade. Don't try to remove any metal just smooth it up a bit.
-
I bought an Armbar Slim last week just to see the differences between the two models. Other than the obvious (fewer tools, slimmer) I noticed a decidedly improved tool retention on the drive arm. The spring arm on the Slim is much smaller but it had more downward angle than the larger Armbar had from the factory. In fact, it's stronger than my Armbar Drive after I modified the spring to increase tension.
The drive arm also had a longer notch at the end for the spring, in part because of the stop put in place due to the slimmer frame. Perhaps this also has something to do with the improved retention.
I'll get some pics up later to show what I mean.
-
I have adjusted the back spring on the Armbar Drive to increase tension for the driver. It worked, but the awl and the scissors are harder to access now. The solution may be to cut a slot in the back spring so that the tension on the driver can be adjusted independently.
-
Forgive me if this question has been asked repeatedly but I understand the armbar was not liked as much because it isn't locking.
However suddenly the Leatherman Bond without locking implements is amazing.
Is the difference in spring tension that much less in the armbar than the Bond? -
@Hvac budget said:
Forgive me if this question has been asked repeatedly but I understand the armbar was not liked as much because it isn't locking.
However suddenly the Leatherman Bond without locking implements is amazing.
Is the difference in spring tension that much less in the armbar than the Bond?I can't speak about the Bond, but the Armbar comes with virtually no spring tension. The back spring servers almost solely as a stop. Bending the back spring a little helps out a lot imo.
-
Good to know. Thanks.
-
Got a Armbar few days ago.
Good blade. Mine came very, very sharp. I found the format of the blade very good. Liked it very much.
No spring snap. None. Zero.
But at this point I had no problem with It, since I used the Armbar to remove some bolts in a very dificult and anoying place and It was made easier by the way that the tool work. If I had a screwdriver with the same lenght of the Armbar It would be more dificult.The scissors are not so good. The ones on my MP400 are better. But It cut everything that I needed without any problem and with perfection.
The bottle opener opened my beer. No complaints.
I'll keep carrying It. [emoji6]

-
I picked up another Armbar during Gerber's 30% off sale. The Armbar Cork will replace the SAK that's with my camping stuff. Overall, it's nicer than the SAK, but the most important part is that it has a lever with the corkscrew.


-
A cracking pic there Rich.

-
Does anyone know how to loosen up the blade on the Armbar? I got one that was extremely stiff out of the package. I tried using pliers to loosen it but that still did not work. Help please. This pivot is not giving. I actually really like the tool set. But I don't carry it because of the blade.


Sent from my Pixel 6 using Tapatalk
-
You could try WD40 or something similar while moving the blade. Be careful with the cutting edge!
If that won't loosen it you could always open the pivot screw. If the armbar is setup like the MP's, you could adjust it that way. It should be set with loc-tite though. So you would have to remove it and apply new loc-tite to prevent it from coming loose. This will of course void the warranty.
I am only speaking with experience from modding the MP's, i have not actually modded the Armbar.
-
@Demel said:
Does anyone know how to loosen up the blade on the Armbar? I got one that was extremely stiff out of the package. I tried using pliers to loosen it but that still did not work. Help please. This pivot is not giving. I actually really like the tool set. But I don't carry it because of the blade.

Sent from my Pixel 6 using Tapatalk
Quite literally 2 months of fidgeting with it... opening and closing it while surfing the internet, and watching movies, and other mindless things.. a good 50 hours of wearing it in, if not more. The moment it opened smoothly, it was all worthwhile.
-
@ElevenBlade said:
Quite literally 2 months of fidgeting with it... opening and closing it while surfing the internet, and watching movies, and other mindless things.. a good 50 hours of wearing it in, if not more. The moment it opened smoothly, it was all worthwhile.Thanks. I did loosen up the pivot with some knipex pliers. It was extremely tight. The action isn't glassy smooth but it is usable now. Thanks for the feedback
Sent from my Pixel 6 using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
