Skeletool???
-
No more so than any other tool I'd guess, but it is worth noting at any rate.
Def
-
@Defender said:
No more so than any other tool I'd guess, but it is worth noting at any rate.Def
Yup.
Well anyhow, I'm still anxious to try one these darn things out. I'm going to try keeping track a little better, but I'll bet pliers, a knife, and screwdrivers make up over 90% of what I use a multitool for. Packaging those three features into as light a tool as possible makes a lot of sense to me.
-
I'm definately still interested in the tool. I'm curious now how both bits are stored in the tool? I wouldn't want to carry it around with one of the bits in all the time...
-
You can see the other bit in the handle with the caribiner. It looks like it is tucked in there somehow. Maybe its magnetic. Looks hard to pull out if it is wedged in there.
Ricky (not Bobby)
-
My big concern about the bit driver being open like that is the small spring that holds it in place is not the greatest. I have had a few LM's right out of the package with springs that wouldn't hold the bit in. In fact, I almost lost the small eyeglass bit from my Surge due to a faulty spring the very first day I had it.
Admittedly it's a simple thing to fix, assuming you are aware of the problem while you still have the bit to begin with. I only managed to save the bit I had because it was inside the tool when it fell out and stayed inside until I opened it again to see what the rattling was.
Def
-
I can see where they store one of the bits.... but what about the other one? Where do you put that one?
-
One in the handle and one in the bit holder.
Joe
-
That's more than any of the other tools hold... except for the XTi and ALX that is.
Good versatility- two bits means four heads.
Def
-
That's pretty well my thought exactly... read my post above! :P
Def
-
If you look at the carabiner, there apears to be a strip atached to the front to clip the strap. If the piece was bent inside the frame of the carabiner it could be made long enough to stop the bit dropping out.
Dave


-
@Defender said:
That's pretty well my thought exactly... read my post above! :PDef
I try to ignore your posts as much as possible :P
@damota said:
If you look at the carabiner, there apears to be a strip atached to the front to clip the strap. If the piece was bent inside the frame of the carabiner it could be made long enough to stop the bit dropping out.Dave
I still don't like it. If you clip the tool onto something, wouldn't you run the risk of it opening up and exposing the bit enough for it to pop out? I think I'd really prefer for both bits to be stored inside the tool. Also, I sometimes wrap my hand around the end of the pliers when I'm using them, to get a bit stronger grip. I don't think I'll be able to do that with the Skeletool unless I take the bit out, then I'm sure to lose it :)
-
All good points, especially the bit about ignoring me! :P
Def
-
My bet is that you are gonna have to carry one bit in the holder and the second one in the handle. They're probably betting that the spring will hold up. ::) Hopefully they guarantee against losing bits cuz the spring fails.
Rick
-
I doubt that. They don't warranty against loss, and they sell replacement bit kits so maybe they tell the QC guys to "go easy" on these ones! >:D
Def
-
Here's some more info
http://www.equipped.org/ORSummer2007.htm
Scroll about 3/4 down the page and there is some more info on the skeletool. Also check out the news regarding victorinox and the new photon. -
Thanks for the link..it'll clear up a lot of confusion about the Freestyle/Skeletool. I peaked on down,and took a look at the Buck Twin Peaks....so help me,I like it,I don't know why,but I like it.
-
Leatherman showed off their new Skeletool in both plain and fancy dress, the Skeletool ($72) and Skeletool CX ($96). They are scheduled to start shipping in November. "Skeletool" was originally shown in prototype form at SHOT Show earlier this year as the "Freestyle." Despite the name change, there will still be a Freestyle, but it will be a more basic version of the Skeletool that will be introduced at a later date.
The basics of the tool have not changed much since the prototype we reviewed in our Shot Show 2007 Report, so I won't go over those elements again except for where the production version has changed. There's no titanium version that was rumored, at least not yet.
Skeletool CX (top)The Skeletool CX incorporates carbon fiber on the frame and the stainless steel frame and blade are coated in black Tungsten DLC scratch-resistant Coating. The combination makes this the classiest looking production Leatherman by far. The Skeletool has a satin finish all stainless frame.
The blade shape remains the same, a cross between a drop point and clip point. It is easy to open via the large opening hole. The Skeletool has Leatherman's standard 420HC stainless, the Skeletool CX gets 154-CM stainless, but unfortunately, unlike that shown in the photos, will come with a combo edge partially serrated blade. Just when you start to get a little excited about a product, they mess it up.
The bit holder is equipped with a rocking button style lock to lock the bit in place, which is an excellent addition. No more easily losing the bit. The pre-production units were a bit difficult to operate, recessed too far to easily press down, but we're told minor changes are planned for production that will make it much easier to use. To use the screwdriver, the tool must be unfolded, which works just fine.
Skeletool Pokcet ClipThe pocket clip looks good, but is a bit on the narrow side; we'll have see how well that works in the long term use. Narrow clips have been known to accelerate pocket wear compared to wider clips. It will differ slightly from that shown on these pre-production models by having a bit more upturn at the tip to ease slipping over the pocket. Based on a very brief test in my pocket, my initial reaction is that it seemed to carry fairly comfortably, like the medium frame pocket knife for which it is designed to substitute. The clip is right hand only and not removable. Being so thin, not being able to remove the clip isn't as big an issue as it is with some knives with bulky clips. I barely noticed it in the hand.
I'm inclined to think that the clip will prove a lot more useful and functional for carry than the built-in carabineer/bottle opener at the end of the one handle. I rarely see knives with carbineers for EDC; that seems to be a narrow niche. No sheath is offered, this is been positioned strictly a pocket tool, a pocket knife replacement, really. It's much thinner than a Charge, for example, and I don't see the need for a sheath.
Skeletool Blade openThe pliers jaws have some very shallow lightening recesses, though how much weight they actually save can't be much, they are very shallow. But, they do look cool. The design engineer we spoke with said that these smaller and thinner pliers still retain about 80% of the strength of the pair of pliers on the Wave/Charge (view comparison).
While the Skeletool doesn't appeal to me, I'm a traditionalist that prefers a folder with a robust blade and a fully equipped multi-purpose tool, there's little doubt in my mind that they will find a ready market for this concept. It is a practical and functional compromise for someone who wants to carry only a single tool in their pocket that serves most of their likely needs. Add pliers and screwdrivers to a knife and you've covered most of the bases for most folks. In many respects, the Skeletool is the closest tool conceptually to a traditional Swiss Army Knife that Leatherman has produced to date.
Wow, that was quite informative. So it seems the skeletool does have a pocket clip, its bit driver will hold its bits in quite securely with a lock mechanism, and the CX version has a (part?) carbon fibre frame, unfortunately no titanium as of yet.
Perhaps the line I found most interesting:
Despite the name change, there will still be a Freestyle, but it will be a more basic version of the Skeletool that will be introduced at a later date
Hmm, I am having a bit of trouble imagining how they are going to simplify a tool which only consists of pliers, a knife, and a bit driver, and also why they would want to simplify what already seems to be the minimum amount of tools people want in a multitool. Maybe they mean the aesthetics of the tool rather than its functions, but then I do not see how that warrants another tool with a different name.
-
I don't understand how they can simplify it either. It's already simple!
-
"will come with a combo edge partially serrated blade..." Grrrrrrr.... >:(
All their knives have the option of either blade style though, hopefully this will too and I just misunderstood.
I'm really releived about the pocket clip!!!!!
All in all its a good report to me, now I just won't know which to buy...
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login