Show off your Sak mod's!
-
This already has its own thread, but I thought I would show off my "Master Ranger Deluxe", or "SwissChamp minus the fish scaler". Essentially I added a magnifying glass/Philips driver layer to a Handyman.


-
Delemont s18. I like this knife, but those ridiculous shaped, overly thick scales had to go. I reshaped the outer liners to a more traditional SAK profile and added Kirinite scales. Also swapped the backside Phillips with corkscrew, and thinking of swapping the nail file with a 91mm small blade.

-
I really like those scales! Nice green
[It's not failure if you learn something from it]
-
@kottskrapa said:
I really like those scales! Nice green[It's not failure if you learn something from it]
+1

-
@kottskrapa said:
I really like those scales! Nice green[It's not failure if you learn something from it]
@pfrsantos said:
+1

Thanks guys

Now I just have to take it apart again because I smurfed up the order of the inner liners
Minor hiccup, but still a pain. -
Almost done peening; pivots are getting tight but I can’t seem to get the heads flat against the scale, leaving sharp edges of the pin heads. I think I need a smaller hammer. Any tips?

-
@trichosirius said:
Almost done peening; pivots are getting tight but I can’t seem to get the heads flat against the scale, leaving sharp edges of the pin heads. I think I need a smaller hammer. Any tips?Not really sure how to help. Maybe cover the scales with some tape, to protect them, and file the head of the pivots with a very fine file or some high grit sandpaper?

-
@pa_strunk said:
Got this 84 mm bundle off eBay (see pic below). Golfer had damaged back spring and broken scissor spring. Climber has weak opening layer and blade spring. Walker is perfect and bantam is good to go. So I broke down the golfer and climber to mix match what works and came up with this golfer variant with Phillips and key ring I had left over from past projects. To the best of my knowledge Victorinox never released this variation of the golfer. Let me know what you guys think.Oh man
This looks quite excellent
Please let me know if you’d be willing to part ways with it [emoji38]Sent from my iPad using Tapatalk
-
New slant on a pruner! 91mm garden knife using saw (everything needs to have a saw!) and the hawksbill blade from a pruning and grafting knife. The brass scales took the longest really as the blade slots in rather nicely. It has a 3.5mm pivot hole so I did make a collar to reduce it down from some tube I found on the ‘bay that was 3.5mm with a 2.5mm inner diameter - what are the chances!
I also has to file a small nick in the combo tool spacer so the tip of the hawksbill didn’t clatter in to it.
I did use liners to keep the saw away from the scale and to provide the .4mm required to keep the main blade tight…yes it’s 2mm like a standard spearpoint.
I guess strictly you might put a small blade instead of the combo but I might carry this too and to be honest because the hawksbill has humped lines too this is one of the few scenarios I like the way the combo looks against the main blade.
Tough as old boots this.





-
Excellent mod

-
Really cool mod and I totally agree with your thoughts on saws
[It's not failure if you learn something from it]
-
super mod, and explanation

The large blade and the combination tool do not rub?
in general the large blade has an asymmetric grind that's why I ask -
Here is a pruning blade I did and still building the knife up.
-
@hulk. said:
super mod, and explanation
The large blade and the combination tool do not rub?
in general the large blade has an asymmetric grind that's why I askMaybe slightly. I was dubious as to if it would fit without any major modification but… it does. As long as you notch the small blade spacer then it sits in their quite nicely.
-
adding a gutting blade and on the back of that may put a 58mm scissors, see what turns up in the future for this growing paper weight.
On the spring of the Pruning blade did you notch it out to stop the blade from hitting. i grind a notch out to get the blade low as i could, yours looks good well done. -
Cheers. No, completely standard blade, just the combo tool spacer got notched to accommodate the point of the blade.
Look forward to seeing the ongoing development of the monster…! -
I'm very tempted to make a Cadet X. I do have one 84mm with scissors (Climber Small) to harvest scissors from, but I wonder if the 85mm Wenger scissors might be a better choice

Also not sure what I need to get it done correctly (and put the Tourist back together).
-
@ComboTool said:
And second, my "Dutch flag" of alox mods. They are cadets with Wenger scissors, with backspring tools as well for two of them.MMMMMMmmmm, nice!
-
@Altis said:
I'm very tempted to make a Cadet X. I do have one 84mm with scissors (Climber Small) to harvest scissors from, but I wonder if the 85mm Wenger scissors might be a better choice
Also not sure what I need to get it done correctly (and put the Tourist back together).
Vic scissors are better (my opinion only) but the 85mm ones do stop you having to rip apart classic old 84s

That said if you want to go for it as I don’t think the climber small scissors have a back tool they should just go straight into the cadet X no fuss at all.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login