Corkscrew or Philips Head
-
Corkscrew. No brainier for me. For all of the above reasons and more. I’ve tried to like the back tool Philips but just don’t. Hats off to the corkscrew!

-
While I carry a Pioneer X most of the time, and a Compact before that, I chose phillips. I have a Super Tinker, but no Climber. If I have a choice (I think 4 layers or less) I'll pick a phillips SAK.
-
Oldest question in the book, the answer is corkscrew, of course. Unless you don't drink red wine, or very cheap one.
-
Plus the corkscrew is great for opening jars, something I learned here - works like a charm!
-
For me it's the corkscrew. I've tried the backside Philips when I EDC'd a Super Tinker and a Deluxe Tinker, but as others have mentioned, I found the limitations of the driver not worth it. I switched to EDCing an Explorer a few years ago and have the best of both worlds IMO.
-
I'm a lot more likely to use the Phillips for its intended purpose. However, the corkscrew can come in handy, and it can also carry additional useful things. These days, I rarely use either, so I don't have a preference.
-
@Rich S said:
How? Refer me to the thread please.Rich, can’t remember which thread it was, but insert tip of the corkscrew under the lid of the tight jar you can’t open, twist gently and if you’ve got it in the right place the seal pops, and hey presto you can open the jar! A neat trick I learned here.

-
I went with a phillips as it is of much more use to me, however after using it a while I think I would prefer it inline rather than as a back tool.

-
I love those red Cellidors man

-
I prefer how the Phillips sits in a pocket, and how it doesn't damage the scale and liner, but that's where it stops. The Phillips is incredibly highly polished, and about the only thing that slips worse is a Chinese cheap MT or SAK clone. I went from most of my SAKs being Phillips to most of them being CS. Also, despite light use, most of mine that I've used extensively show some degree of damage to the Phillips.
And sales will dictate this. Vic has been chopping off SAKs with Phillips like crazy, but leaving the CS variants.
-
Phillips for me as the long driver means I can seal up the recessed screws on junction boxes if I've gone light on tools in the roof(sparky by trade) Do like the CS for knot untying and the classic looks of the Spartan
-
Thanks for everyone's input so far, really enjoyed reading them all and getting your perspectives.
I am surprised with the results as I thought it would be much closer.It looks like this topic has been discussed here at the forum at nauseum over the years, but for a newbie here, it was still enjoyable to hear everyone's point of view, and trends can change over time, so revisiting this topic might still have some value for other newbies here too.
-
Have you guys seen this post? 42 uses for the corkscrew. /topic/40053
- Opens corked bottles (duh!)
- Untie knots.
- Pry the battery out of a cell phone.
- Screw it into a wall and hang your coat on the SAK.
- Staple remover.
- Smooth out the hole you just made with the reamer.
- Clear clogged faucet sprayer.
- Bicycle tire valve tool.
- Holds the micro screwdriver.
- Pick gravel out of tires.
- Rip open a blister package.
- Ice pick.
- Mark a pilot hole.
- Clean mud out of shoe soles.
- Knot the end of a cord. Thread it through the corkscrew. Handle.
- Pop balloons.
- Aides in sewing.
- Clean mud out of sprinkler heads.
- Push used snare wire through it, to straighten out the wire and remove coils or kinks.
- Pulls the drain plug out of a tub.
- Open the corkscrew and screw it tightly into a broomstick-thickness stick. Now open the blade. Tie it securely. Survival spear for fishing.
- Hang the SAK from a piece of cordage from the ceiling. Plumb bob (I have the middle of the handle marked on one mine).
- Corkscrew + a metal lid = a filter or wire mesh for cooking.
- Carry a chunk of C4.
- Pull frozen shoestrings tight, or help loosen them.
- Helps get the innards out of a squirrel.
- Gets the candle stub out of a candle holder.
- Start fights on multitool forums.
- Remove the fuel filter from a lawn mower.
- Although the new corkscrews are 4 turns, you can use them for range estimation.
- O-ring remover for your flashlights.
- Pry out partially-exposed nails.
- Tighten the apron strings on a wrestling ring.
- The inside diameter of the corkscrew is 1/4". I'm sure you know what you can do with this.
- Open just a small hole in a coconut.
- Lift stuck items out of boxes.
- Fish the tape out of a clogged VHS tape.
- Remove patches from a flintlock gun.
- Remove the inside of a shotgun shell, making a blank. Remove the wad and powder too.
- If you don't want the mini screwdriver, the corkscrew can hold a ferro rod.
- Tap a tree for sap.
- Undo zip ties without breaking them.
-
Truly, this is the answer
-
Philips is not the same as Phillips guys!
-
Nobody said the philips could be used as a weapon. I noticed the two openers could be opened, and the philips (or corkscrew for that matter) can be opened, and then the knife can be palmed, closing your hand around it to form a fist with the philips poking out between your fingers, and with those two openers pointing up and down out of the top and bottom of your fist they will make for some wicked jabbing and slashing weapons if you get crowded and don’t have room to swing. The knife handle itself makes a fist pack and the three opened tools add some hurt to the punch. This seems like it would make a heck of a bar fighting tool to get you to the door and out. Or maybe to have tucked in your hand inside a pocket as you cross the parking lot to your car at night, or walk home through a rough area. Corkscrew seems it would be too uncomfortable compared to the philips.
-
Despite the fact that I carry and use both, I voted corkscrew. I find it to be more versatile and get a lot of use out of it even though I’ve only used it on a bottle of wine once.
I like the Tinker family just fine, but the corkscrew wins out for me and I definitely carry corkscrew models more often. Especially since I also always have a Rambler too. Between that and the can opener, I’ve got most Phillips screws covered.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

