Leatherman SIDEKICK / WINGMAN Owners Club
-
They are different but I think it should fit
the Rev pliers are not spring loaded and I believe they are bypass cutters like most all LM except for the Wingman and Sidekick
Just a little tidbit, the Rev and Leap share the same plier head 
-
@Poncho65 said:
They are different but I think it should fit
the Rev pliers are not spring loaded and I believe they are bypass cutters like most all LM except for the Wingman and Sidekick
Just a little tidbit, the Rev and Leap share the same plier head 
Yeah, I’m after the bypass cutters which can actually cut something. I’ve got better chances of getting a cheap Rev than a cheap Leap.
-
Yes, for sure the Rev would be cheaper than a Leap :ahhh :D
-
@Zephon said:
Is there a difference between the pliers on a Rev and a Wingman/Sidekick? My Wingman pliers can’t cut anything right so I’m thinking of dropping in anything that would fit right away.It can’t be that hard, right?
It looks doable, but it appears that it would require some Dremel work.
Rev plier head:

Sidekick (Wingman) plier head:

Both:


I just looked at the Wingman and Sidekick MTs I have. Mine are not great either. Anvil cutters work best when the cutting surfaces actually make contact

-
@Adam5 said:
It looks doable, but it appears that it would require some Dremel work.Rev plier head:

Sidekick (Wingman) plier head:

Both:


I just looked at the Wingman and Sidekick MTs I have. Mine are not great either. Anvil cutters work best when the cutting surfaces actually make contact

Awww nuts. I thought it was a perfect drop-in.
Thanks so much for the comparison pictures Adam!
-
You are welcome

-
Glad someone had the 2 to conpare
Great job, Adam 
-
@Zephon said:
Awww nuts. I thought it was a perfect drop-in.Thanks so much for the comparison pictures Adam!
There are internal backsprings for the plier head in the Wingman/Sidekick handles that keep the handles from flopping around. Without those backsprings, the Rev plier head will drop in. I have 2 Sidekicks. One has the backsprings, in the other one the backsprings have been snapped out.
Handle with broken backspring:

That backspring should extend all the way to the end of the handle:

In the next picture, one handle has the backspring and one handle does not. The plier head is from the Rev:

The left handle will not open any further.
So, you either have to break out the backsprings or modify the plier head. I do not recommend breaking out the backsprings. The handles will flop around a lot.
-
Thank you very much Adam!

As much as I’d want to give the Wingman a fighting chance, seems like the plier head design is more troublesome than anticipated. Must be why they made the Curl / Bond line.
Spare parts are a premium here (example: wave scissors go for USD20) so I can only guess-timate what I see.
Much appreciated!
-
Thanks for checking, Adam

-
Gonna make a confession here - managed to remove an arm of the Wingman from the plier head…..and now I can’t get it back. Yeah, I know there’s a spring of sorts and I’m having trouble keeping it depressed and trying to fit the fastener thru the plier head. Now it’s a bunch of parts in a storage tupperware.
Edit:
After 2 hours, I decided to give it a try again. As I couldn’t generate enough constant force using the Rebar, I ended up opening up the Crunch and using it to generate more force to be able to clamp the spring down. Guess what? It worked!
Used the Rebar as my screwdriver running the T8 bit from the LM kit. I encountered a tight screw which almost stripped the LM T8 while removing it. Had to use a combo of Rebar using the flat LM bits and a ST300 with regular hex bits to tighten the fasteners. After an hour, here are my Sidekick and Wingman all assembled up.
Btw, the Wingman doesn’t close 100%. A tiny <1mm part of the plier head touches the bit changer creating that small gap.


-
Some plier heads are harder than others to put back

Glad you finally got it back together

-
I used a small nail to help align the pivot bolt with the hole in the handle. Then I used my left hand to press the MT onto my work bench. This depressed the backspring enough to allow the pivot bolt to line up with and come through the hole in the handle (using my right hand to push the bolt in).
I will confess that I first thought "Oh crap!" when I first tried to reassemble my Sidekick and discovered just how strong that backspring is :ahhh
-
Rebars are equally hard to put back on
:D -
By the way, this past weekend I started converting the Sidekick with the broken backsprings on the pliers' end into a pocket knife. That wasn't my intent when I bought it, but that's the best thing I can do with it now.
I have not decided what tools will be in it, but I did work on its appearance:

-
I am liking the look of it 8)

-
@Adam5 said:
By the way, this past weekend I started converting the Sidekick with the broken backsprings on the pliers' end into a pocket knife. That wasn't my intent when I bought it, but that's the best thing I can do with it now.
I have not decided what tools will be in it, but I did work on its appearance:


Reminds me of that black and stainless Wingman.
Thanks for sharing your experiences with the plier heads. I swear it wasn’t that bad on a Skele. Anyway, I guess I’ll stick to the inner tools right now and just learn to live with the default plier heads.
-
[attach id=0 msg=2303332]

-
Great pic, Estefan

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
