Tip for adding a hex bit driver
-
@SteveP said:
Well that is a really interesting idea! Do you have one? Can you offer a little review?Unfortunately i didn't ordered one yet, was dead set on getting a couple, but then this bloody pandemic hit big time and have been working at home for almost a year now... :-\ so it became a bit irrelevant for the time being for me....
A mini champ is enough for 90% of my needs for now, with an occasional Climber or Deluxe Tinker.... Have all my tools near by, so the need for SAK SD is pretty limited.
But i'll definitely get a couple when things get back to normal. As long as you don't go crazy on the torque and use it with in Sak use limitations it's a great solution IMO ;)
There are a couple of reviews on YT though. -
MacGyver,
Thank you for the pointer to the YouTube reviews. The SAKlip looks really interesting, but I'm a little concerned about putting torque on a plastic bit socket.
I was able to solve the problem of a 1/4 inch drive 1/4 inch socket sliding off the cap lifter blade by putting a little bit of adhesive putty in a corner of the drive hole and another little bit pushed in the socket side to hold the bit. The putty feels like Silly Putty, but is sticky like Post-Its. Loctite makes some called Fun-Tak, though mine is yellow and I've had it for years.
So, spare socket + old putty = socket and bit solution for $0.
I'll definitely give the SAKlip creator points for creativity, but at 9 Euros for the clip and another 4 Euros shipping, that's $16 for a small piece of plastic. :(
By the way, I like your SAK choice. A MiniChamp has been my daily carry for 25 years. Great little knife that does a lot. I usually also have a SwissChamp in my pocket, but I'm thinking of getting a Climber for when the SC is too big. I looked at the Deluxe Tinker, but prefer the corkscrew over the backside Phillips. And I can add a Phillips with my socket solution. ;)
-
Steve, I am a bit kit Greek. I started bedding SAK cap lifters using J-B Weld to fit 1/4 socket to 1/4 hex adapters. I will leave a link on the bottom of this post.
I did search some Lows stores and Amazon stock the adapter for five dollars each. I found a new easy way to fit the adapter to a SAK cap lifter by putting simply Tacky inside the 1/4 socket side of the socket adapter it holds adapter on nicely.
I played around with a 1/4 socket with the simply Tacky and it worked well but it did not hold the socket very well. A 3mm magnet super glued to the bottom of the bit fixed that. A Leatherman square drive adapter will also fit a SAK inline screwdriver.
Here is the link for using J-B Weld to fit adapters /topic/20136
Sent from my iPhone using Tapatalk
-
@Mike 56 said:
Steve, I am a bit kit Greek. I started bedding SAK cap lifters using J-B Weld to fit 1/4 socket to 1/4 hex adapters. I will leave a link on the bottom of this post.
I did search some Lows stores and Amazon stock the adapter for five dollars each. I found a new easy way to fit the adapter to a SAK cap lifter by putting simply Tacky inside the 1/4 socket side of the socket adapter it holds adapter on nicely.
I played around with a 1/4 socket with the simply Tacky and it worked well but it did not hold the socket very well. A 3mm magnet super glued to the bottom of the bit fixed that. A Leatherman square drive adapter will also fit a SAK inline screwdriver.
Here is the link for using J-B Weld to fit adapters /topic/20136
Sent from my iPhone using Tapatalk
Sounds a bit tacky, but if it works for you...

-
If a 1/4 socket fits onto the large screwdriver, just magnetise it?
-
@kakashi said:
If a 1/4 socket fits onto the large screwdriver, just magnetise it?I haven't been able to magnetize the cap lifter blade enough to hold the socket securely. Putting a small magnet in the socket might work.
Right now I'm happy with using the Winchester hex bit converter. Though I've since found that some Gerber multi-tools have the same hex bit converter and bit set that came with my Winchester, so that's an option too for anyone who's looking.
-
I have made adapters using 6mm magnets bedding the adapter like you would a rifle action to a stock. The simply Tacky (the same as blue tack) for hanging pictures it is non harding works just as good and you and it is easy to do plus you can use one adapter for SAKs, Wingman, Free series tools and on and on.
Sent from my iPad using Tapatalk
-
@Mike 56 said:
Steve, I am a bit kit Greek. I started bedding SAK cap lifters using J-B Weld to fit 1/4 socket to 1/4 hex adapters. I will leave a link on the bottom of this post.
I did search some Lows stores and Amazon stock the adapter for five dollars each. I found a new easy way to fit the adapter to a SAK cap lifter by putting simply Tacky inside the 1/4 socket side of the socket adapter it holds adapter on nicely.
I played around with a 1/4 socket with the simply Tacky and it worked well but it did not hold the socket very well. A 3mm magnet super glued to the bottom of the bit fixed that. A Leatherman square drive adapter will also fit a SAK inline screwdriver.
Here is the link for using J-B Weld to fit adapters /topic/20136
Sent from my iPhone using Tapatalk
I have done almost the same: JB Weld on the inside of a socket. I added small neodynium magnets (Amazon or Ebay sourced) into the JB Weld before it set up, and the lockup to the SAK is great. You can literally swing the SAK around holding the adapter, yet they still break apart when you want them to.
-
I know this is an old thread, but wanted to post that I've found a source for the Gerber/Winchester hex bit kit, without having to buy the multitool to get it!

I saw several of the same Gerber/Winchester multitools on eBay, but as no-names. Assuming these are coming out of China, I took a look at AliExpress.com and found multiple listings for this screwdriver bit set. Apparently they're for Ganzo G200 and G300 multitools.
Most were under $3 !
Nearly all the reviews said the bits were junk, but - funny enough - many of the reviews said they bought the kits just for the bit coupler to use with other multitools. :)
And you get the rubber bit holder with it, so you can put in better quality bits.
I bought two from the Daicamping Multitools Store. We'll see what shows up in a month or so.
-
1/4 bit adapter fits perfectly in the SD/caplifter of my Explorer No gap, it doesnt fall if vertical.
Awesome.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login