Toolbox Challenge - January 2022
-
My Toolbox is ready to go.
I had to take my Leatherman Crater out since the carabiner is a bottle opener. I replaced it with an inexpensive Buck Knife I recently purchased because I wanted a decent, inexpensive knife to use on hard jobs where I wouldn't want to damage or lose a more expensive one.

-
Need to get a pic of my gear setup

That is a nice one, Rich

-
Solid set, Rich. I'll put my starter kit together and take a picture later.

-
This will be my core edc toolkit.
Vanquest PPM Slim
Dedicated Phillips and two flathead screwdrivers
Ares Mini Ratchet
Scissors
Twist ties and zipties
Sanrenmu 6040
1/4" bits
Bottle opener
P-51 can opener
Knipex Cobra 4" and 6"
Knipex Pliers Wrench 5" and 6"

-
Almost time to start this.

I am looking forward to replacing the Executive with a whole toolkit. :ahhh -
@ReamerPunch said:
Almost time to start this.
I am looking forward to replacing the Executive with a whole toolkit. :ahhhThat will be nice, but in a month we'll be looking forward to replacing the whole kit with a MT.

After careful compilation and sorting of data, I have found that I use the following tools most frequently:
-blade
-scissors
-screwdriver
-pliersSo I'm going to give that kit a go, possibly minus the scissors because I really can't find any around the house that I want to carry.
-
Scissors and a Phillips #2 are a must for me. Possibly a blade, so I only included that tiny Sanrenmu, and I like the Knipex stuff so much that I included a bunch. :D
-
Why has everyone else gone so quiet?

I hope to see all of you start this in a few days. The more, the merrier.
-
Replacing the Rambler on my keychain is taking 3 items and even then no scissors, T&T or nail file…however all dedicated tools which should do a better and if not better then as good a job you’d hope.…

The blade on the Bomber B2 is sharp and useful although the handle’s a bit small, still it should be a good rambler replacement for the challenge along with the bottle opener and Vic Quattro SD


-
The Vic Quatro might be pushing it a little bit...

-
Not really different than a screwdriver that can change bits
:D -
I’m good either way so no worries whatever’s decided

I’ve the small SD bit and some larger one piece keychain SD’s as alternatives and will be carrying the Stanley in a maxpedition pouch. Decided against the picquic for now as I don’t want to carry it everywhere
I’m interested in how well I’d go just using the keychain tools and a blade…blade still to be decided

-
Some excellent screwdrivers

-
@Echotech said:
I’m good either way so no worries whatever’s decided
I’ve the small SD bit and some larger one piece keychain SD’s as alternatives and will be carrying the Stanley in a maxpedition pouch. Decided against the picquic for now as I don’t want to carry it everywhere
I’m interested in how well I’d go just using the keychain tools and a blade…blade still to be decided

Is that rust on those key-drivers?
I got a pair of those way back before I joined this forum (and it kind of led to me joining actually), and they looked really terrible even a few weeks on my keys. Fair enough, I guess the steel is not exactly top tier. -
Here will be some of the different bits of gear I will have in January

I am.still undecided about which pair of scissors of these 2 I will carry
one of these is from a Swisscard and the other is a set out of a SAK that I took apart for parts :DI will rotate between the 2 screwdrivers
each have plus and minuses but I like both of them equally
they are Zapwizard handles with Leatherman Ratchet Drivers in each 
I will carry both the Craftsman Adjustable wrench and the Christy Knife daily (I may also carry a Gerber EAB for rougher cutting tasks)
Possible swap traditional pocket knives in and oit during the month as well 
I will carry the Knipex Cobra 6 inch water pump pliers and or the knipex needle nose pliers

So what think you guys :ahhh

-
Nice bit of kit!

-
@ReamerPunch said:
Is that rust on those key-drivers?
I got a pair of those way back before I joined this forum (and it kind of led to me joining actually), and they looked really terrible even a few weeks on my keys. Fair enough, I guess the steel is not exactly top tier.Yep rust but not very bad, more like pitting RP, I’ve had them many years as well
Think I’ll live without them though, not really adding anything over the Stanley and a bit bulky
-
Pretty well decided on this as lightweight and easy to carry …may still need to add the Picquic and possibly larger pliers but will see how I go


-
I am seeing some nice kits!

I will finalize my kits tomorrow. I have 2 Nite Ize Pock-its, so I think I will fix up an at-home kit in addition to my at-work kit. The real problem I will have with that is I only have 1 Knipex 5" Cobra and only 1 Klein mini ratchet. So they will have to be shared between the 2 kits.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login