Curl Owners Club
-
I am in Rich's club now...

-
Congrats, Adam

-
This post probably belongs in the Mods section, but my mods are probably laughably easy (and not very interesting) to real modders. I figured this might be more interesting to Curl owners.
Rich's Curl Mod, Part 1
I was originally going to do my first mod on a Wingman or a Sidekick since they cost less, but then I decided to just start with my favorite Leatherman, the Curl – the size is perfect, and there are a lot of tools that easily drop in with no modifications. I figured this is as easy as you can get for a first-timer.
Step 1 – loosening/removing the screws. I purchased two Torx10 security bits and a heat gun from Amazon. Buying a heat gun just for this mod seemed excessive, but it was only $20 and I’m sure I’ll use it again. The heat gun worked great for loosening the Loctite.

The first mod: replace the 420HC with a better blade – a 154CM blade from a Charge. According to my research, they are exactly the same size and shape. This should be easy.

I removed the screw holding the blade on, and I was careful to not completely remove the post… I just backed it out far enough to remove the blade. Putting the blades side-by-side, they are just slightly different. I hoped it wouldn't cause a problem (it didn't). Note, I was very careful to not lose the washer seen in the pic.

It fit almost perfectly. At first it seemed like the bottom part of the blade near the screw was rubbing against the handle, but it aligned up perfectly after I put on the screw and tightened it back up. Note, I’m not going to put Loctite on anything until I am done with all my mods.

The next mod: get rid of those scissors! Yeah, I know you scissor-lovers are probably flabbergasted over this decision, but I really dislike most multitool scissors. Also, I have almost no use for scissors when I have a perfectly good knife. In place of the scissors, I decided to put in a small bit changer (also from a Charge). A lot of people call it a glasses screwdriver, but I have used the small bit for a lot of electrical devices too.

I hit my first problem. I removed the screw but I couldn’t back the post out… it seems to be stuck on something. Doh!

I used a Torx bit on my new Picquic to remove the pocket clip.

Ok, according to my calipers, the small bit changer is 1.91 mm thick.

And the scissors are 2.45 mm thick.

I need to add another tool to make up the .54 mm difference, but no tool is that thin. I have a couple brass washers (again, from a Charge). Two of them together are .52 mm thick… that is just about perfect! Note, in some pics you'll notice that I used a Torx screwdriver that had a shaft of almost the same diameter at the "tool hole" to help hold, align, and measure the tiny parts.

I decided to put 1 washer between each of the 3 tools. I have no idea if that’s a good idea or not. I didn’t put Loctite on in case I have to change it. Note, this was the most difficult part of the mod – my big bumbling hands along with tiny parts (it’s a miracle I didn’t lose any of those washers) didn’t make a good combo.

And here she is!! Phase 1 of Operation Curl-Charge complete.

Next, I need to replace that can opener with something useful. Right now, I’m not sure what… I also have plans for a difficult mod on the file side.
-
Great bit of modding, Rich
Lots of great pics and great explaining of everything as well 
Blade swaps are always great and I did this many years ago to my first gen 2 Wave

I love scissors but if you find that the small bit driver has more function for you then that is great and the purpose of modding a tool to fit ones needs

-

I always like it when one mods his tools to meet his needs!
-
Thanks Poncho and Zephon

-
Nice job Rich, love it when someone personalize its tools to fit their needs (and becsuse of this, never think of a mod and/or well-done hack as laughable or non interesting), and take time to explain the in's and out's!!!

Will be waitin' for part two pal...

-
Thanks Juan. Even though I already have the parts for the next planned mod, it will probably be awhile before I do it because my Honey-Do list is getting pretty long.
(In case others are not familiar with the slang, "Honey-Do list" is the list of things you wife wants you to do.)
-
Excellent write-up of your Curl mod, Rich.

-
@hsherzfeld said:
Excellent write-up of your Curl mod, Rich.
Thank you

@hsherzfeld said:
A saw?
No, but I am considering replacing the can opener with a saw if it fits.
-
No, but I am considering replacing the can opener with a saw if it fits.
A Rebar saw, I presume?
Just from eyeballing my Bond's (Rebar) saw and my Curl, I think the saw would fit in the can opener's position, but I think it would interfere with the plier head when folded.
If you do try it, let us know how it goes!
-
How's the overall experience with the Curl? I am in the market for a nice pocket MT after wiping out my SOG poweraccess after almost 3 years of daily carry.
-
The Curl is a good tool
It has my most used features from a Wave in a slimmer package

-
I was just looking up best prices for it. I think I found my new EDC. I prefer a leatherman to a SOG MT any day anyways.
Edit: $90... Ouch.... I will just suffer with a Wave pocket carry for that price.
-
Oh yeah
The prices recently went up across the board :ahhhI ended up getting mine for about $65 and we'll worth that price but not the price they are going for now

I even checked the place I bought mine and they are already at $89.95 and out of stock

-
@Poncho65 said:
Oh yeah
The prices recently went up across the board :ahhhI ended up getting mine for about $65 and we'll worth that price but not the price they are going for now

I even checked the place I bought mine and they are already at $89.95 and out of stock

Its been happening with everything. Trying to get a computer in 2020-end 2021 was a 9 month wait nightmare. Lot of stress over the last two years with my work. First time in my career of telling people, yeah you broke your laptop and its out of warranty, here's a 9 year old thing to hold you over.
-
Crazy times for sure

:ahhh :ahhh :ahhh
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login