The Fantabulous February MiniTool Challenge!!!!! 2022
-
Day 7 of 28
1 week down and 3 more to go :o
Been doing well with mine so far but haven't worked in a few days because of Dr appointments and weather
:D


-
Hello day 7.
Been busy with a Nanoblock project so the Mini has been handy in removing mis laid bricks.
Nanoblocks are like Lego but 15mm long and 3mm deep.
This project is over 1100 blocks and will post pick when done.

-
Day 7
Today I will report the use of another multitool other than the :ahhh Mini :ahhh . I normally carry a Micra and use it to trim and file my nails. Since I am carrying the Midnight Manager SAK this month (for the Philip's head), I decided to try using those scissors instead. The small SAK scissors were too small for the task, so I gave up after one nail and I used my Micra for the rest... MUCH better


After I was done trimming my nails with the scissors, I actually tried filing my nails with the :ahhh Mini :ahhh file... I would say it is a less than ideal file for finger nails, but it worked.

-
Day 07

-
Day 7
.

-
Great pics today, guys

Thanks for the report, Rich

I used the wire cutters again today but nothing else

Not been using a blade as much lately

-
**Day 8
February 8**
I’m excited to post this one!
I used the can opener of the Mini when I was preparing breakfast this morning!
It goes without saying that here are my observations:
Steps to use the can opener:
- Open up the tool
- Fold out the handles to deploy the can opener.
So far pretty normal, right? A Wave/Surge/Curl or Rebar/SuperTool/Bond and every other MT with inside tools would follow the same steps.
See the first picture? When applying force to pierce the lid, the encircled pivot would want to fold (since it was designed to work when applying force to the pliers and not the can opener). This leads us to….
- Close the MT. See second picture.
This is our instinct — If the implement folds over, we close the tool to try to hold it in place. The handles do not to lock in place enough to keep the can opener from folding at the pivot, so we close the tool in the hope that it will keep the can opener in place.
The third picture shows the need for my thumb to help press down / keep down the edge. Either way, the Mini’s can opener will open a can.
Will I use it to open another can? Hell NO. If it was any other day like this Tuesday, I’d rather get the SAK Waiter on the cupboard. On SHTF situations like emergency evacuation or whatever, you’ll be glad to have the Mini with its can opener.
It will cut

Personal note:
Here’s the thing — I don’t have any other can opener in a tool smaller than 84mm. Although 80% of canned goods in the grocery these days are easy open cans, I grew up as a boy scout during an age where easy open cans only came from imported goods from the US. In an unlikely event where we’re forced to evacuate, the relief supplies are sure to be canned goods BUT, being government procured from the lowest bidder, most likely will NOT be easy open cans. Then again, if it’s a planned evacuation, I’ll most likely have a bigger/better tool with me.


-
Great use pics !

-
Day 7
After drilling a pilot hole, I decided to manually drive this screw into a project on my work bench. Gave me a chance to use my Leatherman Mini bit driver mod. (a very simple mod/accessory that I will openly admit that I am WAY too proud of) :D


-
Great usage pics Zephon and King_Gorilla

-
Day 8
Just a photo at the shop this morning:

-
Great pics for Day 7 all
and an awesome start to Day 8
Glad someone used the can opener

I never use a can opener in the last several years :ahhh and have only used a bottle opener very rarely as well

I may have to get a glass bottle Coke just to use it :ahhh :D
-
Day 8 of 28
Just another day :ahhh :D


-
Thank you Zephon!
Your experience with the can opener was exactly as I imagined it would be since the handle folds, but I'm glad that the Mini can opener will, in fact, open a can. 
-
Awesome report, Zephon. I never need the can opener on my multitools, but I was really curious if the Mini's unique style can opener worked. I'm glad you tried it and gave such a detailed report

@King_Gorilla said:
Day 7After drilling a pilot hole, I decided to manually drive this screw into a project on my work bench. Gave me a chance to use my Leatherman Mini bit driver mod. (a very simple mod/accessory that I will openly admit that I am WAY too proud of) :D
Let's get a closer look at that cool mod!

-
Day 8
.

-
Day 08
Spanky needed some coffee after work. :D

-
Lovely view behind the mug ! :D
-
Awesome pics today, guys

Day 8 has a been a good one and I may have even used the blade once today :ahhh :D
-
Hello day 8.
Second to last character today.
Nice pics from the rest of the team.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login