DIY sewing project : the "perfect" EDC chaise (that may never succeed)
-
@m47mu74nt said:
Yes exactly, I know I'd also mostly use the ZigZag .. But the fact you can have virtually an infinite amount of stitches by swapping cams is
Lol,, it’s interesting!
JR -
Still making pouches instead of a bag

double zipper, loops inside and outside, super light ripstop fabric
.jpg)
.jpg)
.jpg)
.jpg)
-
Nice job!

JR -
Thanks

-
I think I might have fixed my machine, normally the string would get so tight and end up snapping when I was sewing something, I had the tension loose but it was still getting tight, I bought some super strong string and it kinda worked but still snapped so I had to look the machine over, I tried taking the one part apart but I got it to loosen up, so I took a piece of scrap and put some normal string on it to run a few lines back and forth and it worked fine, so maybe, just maybe I got it working again?
JR -
Those pouches look great! I'm sure if you opened up some commissions they'd sell

-
@MadPlumbarian said:
I think I might have fixed my machine, normally the string would get so tight and end up snapping when I was sewing something, I had the tension loose but it was still getting tight, I bought some super strong string and it kinda worked but still snapped so I had to look the machine over, I tried taking the one part apart but I got it to loosen up, so I took a piece of scrap and put some normal string on it to run a few lines back and forth and it worked fine, so maybe, just maybe I got it working again?
JRThat'd be great!
Mine sometimes winds up the thread around the bobbin pole, so it ends up making a knot and locking it down@GearedForwards said:
Those pouches look great! I'm sure if you opened up some commissions they'd sell
Thank you,
They might, but I'd need to sell them quite highly priced depending of the fabric used. And not sure quality is high enough for sellable products
-
It’s this thing right here, it’s suppose to keep a tension on the string but only so much, but mine was literally locking onto it and causing the string to snap, even though I had the tension as light as possible, but I kinda did a little finesse with a screwdriver and I think it worked??
JR
-
@MadPlumbarian said:
It’s this thing right here, it’s suppose to keep a tension on the string but only so much, but mine was literally locking onto it and causing the string to snap, even though I had the tension as light as possible, but I kinda did a little finesse with a screwdriver and I think it worked??
JRI had that issue on my SInger type 15, not built the same, but similar principle : the tension discs/mechanisms were seized and did not release when unscrewed
-
Hey, I did something and the couple test runs I did were perfectly fine so as long as it just keeps doing like it was on the test runs and not before I don’t care what I did, lol.
JR -
Simple tissue pouch : ripstop polyester fabric, 13cm YKK zipper, "Laser" brand polyester thread, French seam and no internal lining to stay super light
.jpg)
.jpg)
-
Homemade 5.11 covert panel ... Because I couldn't find any in "tungsten" color on the market.
It is not a perfect match (the fabric I have isn't quite the same, and I didn't have the right thread color) m, but close enough for sure.
(I even put a little tab to mimick the 5.11 logo tab on the lower right hand corner)
Below the homemade panel is the commercial one in kangaroo color I used for reference.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login