New (2007) Spyderco Spyderench
-
Yikes! :o Call me a sheeple if you want...that one scares me!
-
Got the SpydeRench today. Curiously, the sheath comes separately rather than in the box. I opened the box and fiddled with the SpydeRench a bit. Unfortunately the plain edge portion of the blade has a nick in it. :( :( :( The box was sealed with stickers on both ends so I know it wasn't a demo knife.
-
Awww, that really is a bite! :( Nothing worse than having your anticipation soured by a new tool with a defect!!
So now you have to go through a bunch of hassle to return it?
-
Although it is a little disappointing that it wasn't perfect out of the box, I haven't decided if the nick warrants returning the SpydeRench. The blade nick isn't very big and I'll probably nick the blade up with use. It does make me wonder how well the edge will hold up with use but it is my (uneducated) understanding that AUS-8 is excellent steel. Perhaps the durability of the edge has more to do with the grind?? The nick is located where there is a ridge in the "liner" and the nick was most likely caused by blade hitting the side of this ridge during assembly--not exactly heavy abuse.
This brings up another issue. The blade has some wobble especially near the closed position. This wobble will allow the blade to hit the side of the "liner" if you don't close the blade carefully. Undoubtedly, that's how the blade was nicked. I know that I didn’t nick the blade since I noticed it when I first opened the blade, before I ever closed the blade. I'm going to write Spyderco about the blade wobble.
I also noticed that the Phillips/Punch/File does not fit in the bit holder. The Phillips on the end of the file isn't very practical without a handle to provide additional leverage. Of course, the included Phillips bits will be sufficient for most tasks but the long Phillips on the end of the file would be useful for deeply recessed screws.
Another problem that I noticed is the spring that holds the file tends to pop out when removing the file.
After doing some comparison with the photos from Tom's post, I don't think there is much difference between the ByrdRench and the SpydeRench other than the differences that I previously noted. Unless the diamond file or the AUS-8 blade steel is a big selling point for you, you might go with the ByrdRench instead.
In general, I would say that the SpydeRench is more toy than tool. I suspected the same thing about the CRKT Guppie and avoided it for that reason. My guess is that the construction of the SpydeRench is much better than the CRKT Guppie but it's just a guess. The SpydeRench is a fascinating design but I think the new, improved SpydeRench could use additional improvement.
After I figure out whether I need to send the SpydeRench for repair, I plan on carrying it and then writing a full review.
-
Nice, great photos too.
I do have a question on the bottom right photo.
Is that a spring I see?
-
I believe that spring is for holding the file/sharpening rod.
Def
-
It might also be used to launch the file at an armed assailant--a mall ninja, for instance.
-
Or you might slip and put your eye out.
-
Not to mention a ban on tequila.
Def
-
Here's a photo showing the problem with the SpydeRench.

Today, I received a replacement from Spyderco. The replacement has far less blade wobble but there's still a bit of play--mostly near the closed position. The replacement doesn't hit the "liner". I had a chance to use the SpydeRench a little bit before I sent it back to Spyderco (haven't used the replacement yet). The wrench worked well (replaced a car battery) and the knife is scary sharp. The magnetic bit driver works ok but it lacks reach. The magnet holds the bit in place but isn't strong enough to keep a screw from falling to the ground. The round nose slip joint pliers are neat but they lack leverage. The sheath isn't the best but I prefer using the pocket clip anyway. I probably won't have a chance to write a full review for quite a while since I've injured my shoulder and will have surgery in September. ...stay tuned... :P
-
I feel your pain;I bunged up the rotator cuff in my left shoulder many years ago trying to lift a patient twice my weight...it took lots and lots of physical therapy to make things right again.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

