A7 size Notebook cover (WIP)
-
-
-
Now begins the noisier/harder part: hammering through the leather. Once you've pierced throught it, use a ruler to free the fork from the leather. If you pull on it, you may stretch it out of shape.
Once you've made the first 7 holes (if you read the previous post, you know why there's 7 and not 8), proceed to make another set. Here's a tip: use the previous last 3 holes as a guide, to keep the line straight. Make the aditional 5 holes, remove fork. Repeat until you come to the end of the line. Adjust the fork for making just the needed last set.
You now have the smaller piece ready to be stitched to the larger one. To ensure the holes align perfectly, use the smaller piece as a guide for making the holes in the larger piece. Gently pass the fork's prongs through the holes of the smaller piece and, after making sure it's well aligned, hammer away. Use the same "3 holes guide" trick and punch the holes in the larger piece.
**Attention: the two pieces are going to be stitched together with their rough side against each other. To use the little one as a guide, place the smooth sides together.
**
This time, add an extra hole after each end.



-
After the last step, get the rest of the materials you'll be using: waxed thread, two blunt needles (I use a saddle stitch, you need two needles for that), scissors, lighter. The thread is the least expensive of these materials, so don't be affraid to use more than you need. Nothing worse than, after stitching 3 or 4 feet of a project, you find you needed another 2 inches of thread. Don't ask me how I know this...

Ok, take a length of string approximately 5 times the length of the stitching you're about to do. Get one needle in either end, with some thread hanging away, and pass the thread through the hole where you're starting you stitching, leaving half of the thread on either side.
I awlways start on the 2nd or 3rd hole, stitch to the end and stitch back over the holes until y«the end, where I, again, stitch back over a couple of holes. This ensures a stronger stitching and a better looking one, too. See the second pic? That's why you have the extra hole in the larger piece, to have the smaller one's edge flat against it.
While you proceed, try to awlways do the same sequence: I start from the inside, taking care when passing the outside needle in, not to "stab" the thread awlready coming out of the hole. After you cross the thread, pull gently on both ends to make the stitching snug. Not too much, or you can deform the leather (especially thin pieces, ike the ones here).




-
Getting to the final holes, do as in the beginning and pass the thread back again, over the last couple of holes. Cut the thread on the inside, leaving about 5mm. Waxed thread burns very easily, which is good for this last part. Use the lighter and melt that little piece of thread. When it's getting close to the stitching, press it with the side of the lighter. It'll create a flat head that will prevent the thread from escaping through the hole. Pass the other thread through the next hole, repeat.
I like to have these melted ends on the inside/bottom of the work. It's where they're least noticeable.
And the first part is done. This flap is for holding a spare notebook or to keep some pages/notes taken from the notebook being used. Or anything else you fancy.
More on this in a few days, if awl goes well.
Thanks for watching!





-
-
-
Nice work!
Skickat från min SM-G996B via Tapatalk
-
Second half, here we go!
Since this piece was awlmost asquare, I made a note on the inside, so as to position it correctly. I usually do this. The notes will be on the inside and not seen, so that's ok.
Again, use the compass, with the same width, to mark the line for the holes to be punched.
Read the previous posts for what comes next, yadda yadda yadda...




-
-
-
At the end, that's the little piece of thread I leave to be melted.
And it's done!
Back and inside view. The stitching makes it easy to know what's the top and bottom.
The two inside flaps allow for two different types of pocketbook: side opening or top opening (like the one showed). The "unused" flap can carry an extra pocket book or some pages, notes, cards, etc.




Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login




