Show off your Sak mod's!
-
Noooo, way beyond the reach of my abilities.
From EBay, a Russian seller, I assumed they were Victorinox OEM.
Sent from my iPad using Tapatalk
-
@SAKTaschenmesser said:
Lightweight Huntsman:- Wood scales
- Old style scissors, screwed pivot, no back tool
- Combo tool is a bit stiff, hopefully it will loosen up
Can’t argue with that combo

-
Yes, my favourite toolset is:
(1) Blade/Combo
(2) Wood saw
(3) ScissorsThe Lightweight Huntsman.
I have limited tools and experience, but have made up one 91mm with red scales and another with wood scales.
This is my latest, and last, I've got enough!
84mm in Alox.
I was going to make it in red scales, but Myron tempted me with Alox, which I've never done before.
The peening is rough, but it works. I think I need to hammer it home further. Unfortunately there is a hammer mark just below the pivot north of the cross. I was using a punch to round off the pivots and it slipped. Impatience and lack of attention to detail.
Many thanks to the generosity of Myron who supplied most of the parts.

-
Such a cool knife! And you did a great job peening those pins over. So fun to see how this looks in an 84 mm frame, too.
Excellent work, @SAKTaschenmesser!
Myron
-
It’s a great toolset, and nice work so far!

The nice thing about errant mark in your own knife is you get to use it without worry about doing any cosmetic damage.
A small radius ball peen hammer might help tighten the rivets as needed. I use a heavy hand to set the rivets and fill the conical seat in Alox or brass bushings, but small lighter taps for rounding exposed rivets (if not setting them flush/flat to the level of the alox face). Small radius helps to ‘safely’ work closer to the edge of the domed head. Light taps, using wrist action only.
-
Great mod!
But...@SAKTaschenmesser said:
This is my latest, and last, I've got enough!Yeah, right!
-
An example might help show what I mean about the peening and finishing.
This is a before and after of a 91mm center/3rd pin that was flattened on the backside when reused and re-set in a mod.
The peening marks are made close and small enough to resemble a golf ball or mirror/disco ball somewhat and are fine enough to be sanded or polished away.
Just takes a little more time and some patience.


-
Thanks, the knife's tools are pretty tight. If I do feel a bit of wobble develop, I'll give the pivots some fairly gentle, progressive taps with the ball of my hammer to get it just right. I quite like the hammered golf ball look.
-
@SAKTaschenmesser said:
Thanks, the knife's tools are pretty tight. If I do feel a bit of wobble develop, I'll give the pivots some fairly gentle, progressive taps with the ball of my hammer to get it just right. I quite like the hammered golf ball look.
I didn’t mean to confuse the issue regarding tightening. I only meant that as a ‘if needed’ part of the discussion. Like needing to refinish after additional tightening. I’m primarily demonstrating a finishing technique I use after the rivet and tools are set. So mainly to show the difference in cosmetics. My example above was already tight, but with that big ugly flat top.
I hope that helps you and anyone else looking to improve the finish of their peening work. It’s just a matter of removing the large ‘facets’ and replacing them with smaller finer ones that can easily be made to ‘disappear’, wear, or polish away. :)
-
Say bye-bye to the compact,, it was my Xmas gift, ah man am I nervous,,
JR
-
I guess there’s no turning around,, :-
JR
-
Update, I needed a break, yeah that’s a Philips on the back rather then a corkscrew, I just don’t see the point of one, and yeah there’s an extra layer, but what could it be?

JR
-
All peened and ready for scales!
JR
-
Who’s ready for the end product? Any guesses on that 3rd layer before I post a pic?
JR -
Oh well, here’s the finished product,,
Took out the corkscrew and put in the Philips and added a whole extra layer adding a saw, I thought of putting a awl on the backside but decided not to, this little guy is almost perfect, the only thing it’s missing is alox scales,,
JR
-
Alox is nice when you can get plus Alox. I'd take pen/pin/T&T over Alox without. Nice mod.
-
@MadPlumbarian said:
Who’s ready for the end product? Any guesses on that 3rd layer before I post a pic?
JR1 layer without back tool?
I'd say old metal file or woodsaw? Or a fish scaler -
@MadPlumbarian said:
Oh well, here’s the finished product,,
Took out the corkscrew and put in the Philips and added a whole extra layer adding a saw, I thought of putting a awl on the backside but decided not to, this little guy is almost perfect, the only thing it’s missing is alox scales,,
JRDamned, my post did not "post"
Saw was one of my guesses : you made the "wood guide" pendant of my trail guide
-
Cool,
JR -
@MadPlumbarian said:
Cool,
JRBeware, this might become your favourite EDC

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login