Juice CS4 opinions
-
The only thing about the Juice that might get ya peeved is You are giong to get grit in between the alluminum scale and the liner. It will not effect the preformance at all but the grinding of it when you grip it is kinda a bummer.
Take that with a grain of salt. I have got used to it, and it does not bother me anymore. By the way what you run. I play daily with a Cat 235.
-
The core and surge have the same jaws. As they came out after the Charge (same jaws as Wave, Blast, etc) and they have the same style, I would bet they are probably the best big jaw tools out there right now. If you like the simple style handles (PST, etc) then get the Core, but if you like the Wave, get the Surge. I got a surge and I like it, but it is way heavy for me. I carry around one of my regular size tools most of the time.
Rick
-
The CS4 is good, but I don't like how the handles aren't the same thickness.
HAHA, I thought I was the only one to be so picky as to let that bother them, but that's been anoying me since I first saw the Juice series. Oh well... But it's nice to know I'm not the only one. ;D
The Juice has a unique niche in being SAK-size pocketable with a usefully larger pliers than any offered by Vic. Because it is a quirky little tool, I don't mind the uneven handle width. Since it doesn't interfere with function, I consider that part of it's charm, along with having to raise the awl to open and close the saw. In use, the CS4 performs equivalent to a SAK. It has a sharp PE blade and saw equal to the same size Vic, which is good as they get.
As for the other implements: the cork assist is problematic. After chipping a bottle lip and springing the tool in a leverage attempt (fixed no charge by Leatherman), I no longer use it for that purpose. Instead, I turn the corkscrew almost all the way down and lever the handle on the lip to break adhesion. Works every time.
Screwdrivers are stubby, no reach for deeply countersunk or hard to get at screws, but they are sharply finished, less likely to slip than their SAK counterparts. This is one of the things I like about Leatherman drivers v. SAK. The can/bottle opener is just adequate, but will get the job done. The awl came sub-par, but benefitted from a session of sharpening.
My CS4 has held up well to moderate use, but I don't expect it to sub for a full size tool when it's necessary to really crank down on something. Suspended by dummy cord into a jeans pocket, I can forget about it until needed for something. I think that it's a good multi-tool for something of that size, and if pliers are important to you, the only choice.
-
How exactly does the assist work? I could never figure it out.
-
I think it works by you showing the tool to your friend, then he ASSISTS you by opening up the bottle because he wants to figure out how it works :)
-
I think it works like the more fancy versions, but like all the multitool features it is a good substitute that works in a pinch. To make it work, you screw in the corkscrew until it is almost all the way in, then tip the handle (with the assist partially extended) until the notch on the end of the assist rests on the edge of the bottle (it kind of straddles it). Then lift up on the handle and allow it to pivot around the axis of the assist. It should give you enough leverage to pull the cork out.
Rick
-
@hawkchucker said:
Take that with a grain of salt. I have got used to it, and it does not bother me anymore. By the way what you run. I play daily with a Cat 235.I usually spend most of the day on a Case 590 backhoe. We also have an ancient cat, not sure what it is though. I was checking out the Surge, I really like it. I might have to see if any local places have them so I can check them out in person. I'm pretty hard on my tools for work so it has to take alot of abuse. Thanks for all the help.
Rob
-
@trickknife said:
I think it works like the more fancy versions, but like all the multitool features it is a good substitute that works in a pinch. To make it work, you screw in the corkscrew until it is almost all the way in, then tip the handle (with the assist partially extended) until the notch on the end of the assist rests on the edge of the bottle (it kind of straddles it). Then lift up on the handle and allow it to pivot around the axis of the assist. It should give you enough leverage to pull the cork out.Rick
Problem is, there is only one notched end. That makes for an unstable fulcrum, allowing the tool to spread out against the rivets enough to loosen them. In addition, all that force on one point can cause the glass rim to chip. Dedicated assists have a double rest for this, which works way better. I think the Juice assist is a problematic design and after having sprung my CS4 with one, don't use it any more. The corkscrew is workable without it.
-
Good point. I don't use the assist either if I can avoid it. If you really did need to use it, you can round of the corners of the notch on the assist. You'd want to buff it real good too with a buffing wheel to prevent chipping. But if your wine has a screw top, then you don't have anything to worry about. ;D Or better yet, if it comes in a box with a rubber stopper.

Rick
-
The only thing classier than wine in a box is wine with a screwcap and expiry date!
Def
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



