Gerber Mp600 owners club ;)
-
Since 2019 Gerber have been stamping production codes on the inside of their MP600’s , has anyone got one that has the code on the inside of BOTH handles ?
-
Nope; both my blunt-nose and my Basic have it only in one, next to the can opener.
-
@Juan el Boricua said:
Nope; both my blunt-nose and my Basic have it only in one, next to the can opener.Thanks Juan , i have 2 needle nose and one blunt nose , one of the needle nose is stamped twice ( one on each handle ) . I did wonder if it’s something they started to do then decided it wasn’t needed.
-
Also I used to think it was a date code but now I’m not so sure , my theory is the last two digits are the year but the first three are the factory or country code of manufacture
-
It is also my understanding that the last two numbers of the code are the year, but the first three might be model number; all my MP600's (6) begin with 087, while the NXT's (2) begin with 915, Dime with 466, and EAB Lites(5) with 897.
-
@Juan el Boricua said:
It is also my understanding that the last two numbers of the code are the year, but the first three might be model number; all my MP600's (6) begin with 087, while the NXT's (2) begin with 915, Dime with 466, and EAB Lites(5) with 897.I totally agree with the last two digits being the year but I don’t think the first three are model numbers because my Mp600’s , Strongarm , Fastball and impromptu pen ( all U.S made or assembled ) start 087
-
Sounds reasonable. Thanks.
-
These are with me today ...
[attach id=0 msg=2343527]
-
Nice carry, Juan!

-
Today's kit ...
[attach id=0 msg=2344194]
-
Very nice!

-
[attach id=0 msg=2358060]

-
Just received another! This one of the Pro Scout variant... [attach id=0 msg=2361982]
[attach id=1 msg=2361982]
...and now we know what is global and what is stil USoA made.

-
Just got a new Mp600 in black and was surprised to see they add the black oxide finish to the serrated blade after the edge has been ground. Never seen this before on a blade
02C3E42A-1943-468F-B9B7-F24E71BF333D by Duncan Moore, on Flickr -
@Dunc said:
Just got a new Mp600 in black and **was surprised to see they add the black oxide finish to the serrated blade after the edge has been ground. **Never seen this before on a blade
02C3E42A-1943-468F-B9B7-F24E71BF333D by Duncan Moore, on FlickrThat was my thought exactly but, at least in my examples, all three of mine were quite sharp; not affected by the oxidation process!
-
@Juan el Boricua said:
That was my thought exactly but, at least in my examples, all three of mine were quite sharp; not affected by the oxidation process!I’d always assumed the blades were sharpened after the knife was assembled to reduce the risk of injuring the assembler. Definitely not the first time I’ve been wrong

-
Today finally my BO MP600 arrived

Now i have Centerdrive, modded MP600, BO MP600 and MP800
Only Tools Matters
-
Very nice Antti, congrats!

Nothing like a brand new BO
-
Just wanted to show off my “Gerber MP600 Drive”. I much prefer the MP600ST as the main tool due to the frame already having cutouts, longer combo knife blade than other mp600 variants, longer Phillips driver, replaceable cutter inserts (I know the carbide ones are junk), and better plastic tool locks on this model similar to the diesel.
Mods:
- Removed AR sight tool and added gerber armbar slim bit driver. Driver tool and MP600 frame both had to be modded a good bit to allow fitment. NOTE: attempted to modify the AR sight tool initially to accept a bit extension but this is not recommended as it is easier and cleaner to just add the bit driver from the armbar, and also allows for another short tool to be added in the stack due to the armbar driver having a slimmer profile.
- Added scissors, Tshank adapter (for leatherman surge file, Tshank saw blades, etc), and large flathead with V notch.
- HSS cutter inserts installed and are much much better. I have cut wire hangers, barbed wire, etc with them and not even the slightest damage.
- EPI insta-black 370SS sample kit on the way to blacken the modified portion of the frame, bit driver, and satin tools.
Also may add Wire Stripper tool from SOG powerlock in near future as I’ve already done this mod to my other MP600 I have.
Sent from my iPhone using Tapatalk



Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


