Problem
-
@Mr. Whippy said:
Agree with the soak. Start with hot water and large volume (4 L would be what I'd start with.) Change the water every 12 hours with fresh hot water, until it loosens up. Then lubricate with mineral oil.Edit to add: At least you're not Belgian! :D ;)
This has got to be good advice because it is exactly what I would have told you to do except change the water every 12 hours using mineral oil.
I think I would have just told you to soak it in hot water.But their way is better I use olive oil.
-
thanks a lot !! i already try to soak it in water, in oil, clean it with a toothbrush....no change.
i think there is something else between the blades, because i can hear a "scronch scronch" noise when i open it. May be sand ?
Did someone try to take apart a swiss tool ? i saw there was crimping assembly.
what get me in trouble the most is the corkscrew...... :D
thanks -
@phil said:
thanks a lot !! i already try to soak it in water, in oil, clean it with a toothbrush....no change.
i think there is something else between the blades, because i can hear a "scronch scronch" noise when i open it. May be sand ?
Did someone try to take apart a swiss tool ? i saw there was crimping assembly.
what get me in trouble the most is the corkscrew...... :D
thanksDid you soak it for a long time though?
Sadly they can't be taken apart. A blast with compressed air may help if a long soak doesn't help.
-
yes, a day in the water and 4 hours in oil......
i think i willl try again.
thanks -
Keep open/close the blades under running warm tap water.
-
I wonder if it hurt it to boil it in some water.
-
soak it in goo gone? maybe?

-
@ducktapehero said:
I wonder if it hurt it to boil it in some water.Shouldn't.
-
Maybe a run through the dishwasher...either that or a high pressure water hose into the parts that are crunching while you move the blades back and forth.
-
@Corrugated said:
Maybe a run through the dishwasher...either that or a high pressure water hose into the parts that are crunching while you move the blades back and forth.+1

BTW welcome phil

-
Perhaps something like this? http://www.lakeland.co.uk/sticky-stuff-remover/F/product/8976
I've never used it on a tool but it certainly works in other applications.
-
@noth said:
Hi there mate, welcome to the forums.
what get me in trouble the most is the corkscrew...... :D
A corkscrew on a swisstool? Do you by any chance mean swiss army knife? I'm not sure how would cellidor react to boiling...
I assumed it was the corkscrew attachment on the Swisstool, but good call to check before those scales go all bendy.
-
mineral spirits might loosen the gunk up...soak/shake
-
@ducktapehero said:
I wonder if it hurt it to boil it in some water.That sounds just crazy enough to work

Then zap it with WD-40 afterwards

-
Gas? I know its harsh but shouldnt be too bad on the finish. Then soak in some detergent and lightly oil
-
Do you have a Ultrasonic jewelry cleaner? Those things do wonder. Just let it soak in a water bath and give it a few cleaning cycles. I bet that would work out the gunk in no time.
-
@phil said:
yes, a day in the water and 4 hours in oil......
i think i willl try again.
thanksHot water is an OK solvent.
However, since hot water isn't working I'd go straight to a more righteous solvent - acetone!
Acetone won't hurt the stainless steel, but it should dissolve the organic crud that's gunking up your multi.
(If you don't have acetone around and don't want to buy it, try turpentine or even gasoline. Be careful - all of these solvents are highly flammable and give off toxic vapors.)
.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login