Squirt ES4/PS4 Owner's Club
-
I am not sure I remember much apart those mods and it really is a shame that the pics are gone

Probably the faulty of Photobucket I am sure ::)

Never had one apart myself or else I could at least help or comment about it

-
Found a YouTube video
https://youtu.be/tWr9x9Mymbw -
I remember that being in a thread about Squirts somewhere else here on MTO
would definitely give some good advice and POVs about how to take them apart and put back together

-
Well, drilling rivets is not easy. And pounding them out can least to this.
So next cheapest S4 is on eBay is on its way.
I also managed to lose the keyring so. I'll need those 2. It also put a stop to my thought of stealing the Phillips from that worn out E4. Way way too much work.On the plus side the 3d modeling is going ok but I'm going to have to create the tweezer holder since the one there was didn't fair well with the heat of burning off a rivet right by it.

-
:ahhh Hopefully the next one will go better

I have broken individual tools while trying to mod them as well
can't make an omelet without breaking a few eggs unfortunately
:DA side note, if you aren't trying to keep the rivets or the scales then it might be best to take a Dremel and grind the face of the rivet off down past the face of the scales a bit and it should make it easier to punch through

Also a small nail (possibly ground flat on the end with a point with above said Dremel) that is undersized of the hole would be better than an actual punch (what were you using BTW
)Best of luck in this mod and I still can't wait to see the end result

-
status update, the scales and the tweezer sheath are all done for the most part. i'm investigating chamfering the edges, and recessing the lettering into the scales.
I need to find the Font leatherman uses so i can match the lettering if anyone has any idea what font they use.@Poncho65 said:
it might be best to take a Dremel and grind the face of the rivet off down past the face of the scales a bit and it should make it easier to punch through

yeah that led to melting the tweezer holder.
@Poncho65 said:
Also a small nail (possibly ground flat on the end with a point with above said Dremel) that is undersized of the hole would be better than an actual punch (what were you using BTW
)I'm using a section of 1/8" brass rod, to drive since it is not as hard as steel it shouldn't harm it but the scissors were just left unsupported as i was tappy tap tapping. and there is very little metal around the pivots. so snappy snap snap it went.
-
Never modded a Squirt so never had to worry about that type of plastic :ahhh

The 1/8 brass rod would probably be better but I always have problems of it bending is why I suggested the nail

Also, I can't wait to see the new scales and the tool as a whole 8)

-
If anyone is looking for a Squirt that is more suited to "modder fodder" here is a PS4S (it has scissors) wih torx pivots (a lot easier to pull apart and put back together again than the regular riveted versions):
-
@gregozedobe said:
If anyone is looking for a Squirt that is more suited to "modder fodder" here is a PS4S (it has scissors) wih torx pivots (a lot easier to pull apart and put back together again than the regular riveted versions):not that many of those anymore. too bad the seller did not recognize the worth. maybe the buyers do
-
@Poncho65 said:
I can't wait to see the new scales and the tool as a whole 8)

kind of hard to see given the background but It should be done in the next hour or so
if anyone wants to watch
https://app.obico.io/printers/share_token/e6b0b2394e3998b5ab8960ba36cf920d8b3e/ok done and installed. There is an extinction of detail in the leatherman text along with some of the other text. I kind of expected that. I need a smaller nozzle size. I am currently running a 0.4mm nozzle. the parallel lines you can see in the letter N and S4 would be thinner, and the details that would be captured in the letters would be higher.
Changing nozzles on my current extruder is a huge PIA but I have been meaning to, for the last 2 months, Install a newer extruder that makes nozzle changes a snap and for that extruder I just received a 0.25 nozzle, So perhaps this week I will get around to swapping it out.
-
Looking very cool, cnlson

-
finished and going on my keychain.


-
Looking great, cnl

-
Great pic and carry, Adam 8)

-
Very nice Adam!
Sent from my SM-A326U using Tapatalk
-
Nice one, Adam

Had to pull out its brother

[attach id=0 msg=2385637]

-
Thanks, guys

Nice pic, nakken. I need to get a PS4 and a P4.
-
Thanks Adam

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
