Show off your Sak mod's!
-
@pfrsantos said:
+1Awlso, why the combo tool instead of the bottle opener?
??? ???
Sure. I noted that I saw a 91mm Spydernox being built, don’t remover where, and they made no modification to the blade at all. They did how ever modify the spring to accommodate the Dragonfly. I prefer the the Combo Tool. Hindsight sight saws I should used a small blade vs. the can opener.
-
can you explain the process of puting the dragonfly blade?
Modifying the spring OK but for the pivot diameter?
-
Millions of SAKs and swiss army like knives get sold cheap on eBay and secondary markets due to broken scissor springs or scales. I put a Victorinox spring on this Syracuse #381 made in Poland sometime in the early 60’s. If you choose to do this it only takes about 30 minutes of dremel work to have an “improved” SAK with fully functional scissors. Also added a better nail nick. They did not know a lot about leverage in 60’s apparently.

-
New custom painted scales. I could not fine 84MM Plus scale let along 84MM Plus scales in the right shade of blue. So I made some.


-
Nice blue!
JR -
@trouthunter said:
New custom painted scales. I could not fine 84MM Plus scale let along 84MM Plus scales in the right shade of blue. So I made some.Looks cool. What kind of paint and what kind of surface prep did you use?
-
@Enginears said:
Looks cool. What kind of paint and what kind of surface prep did you use?Just standard spray paint with a matte polyurethane clear coat. Surface preparation was simple sanding and washing.
-
Was very unlikely to find one of these so modded a divot tool to make this Spartan golfer out of a sheet of 1.5mm 403 stainless. Looks pretty convincing not sure how bend resistant 403 is/will be but unless I hit a large stone I’m sure it’ll be fine.
Meant to take photos of fitting up but forgot in a flurry of activity but you can see the template I made by scaling one of the photos on SAK wiki and tracing around with Adobe illustrator pen tool. For the pivot end I just traced around a pen blade….

-
@Helvetica Bold said:
Was very unlikely to find one of these so modded a divot tool to make this Spartan golfer out of a sheet of 1.5mm 403 stainless. Looks pretty convincing not sure how bend resistant 403 is/will be but unless I hit a large stone I’m sure it’ll be fine.
Meant to take photos of fitting up but forgot in a flurry of activity but you can see the template I made by scaling one of the photos on SAK wiki and tracing around with Adobe illustrator pen tool. For the pivot end I just traced around a pen blade….Looks good! Keep us posted on the durability of the 403.
Here is a 3 layer I put together last night. I call it the camp and climb. Basically a climber with a blade swap. Added an extra liner for the woodsaw/small blade - now it fits like a charm.
[attach id=0 msg=2386642]
[attach id=1 msg=2386642]

-
Looks like you managed to get good clearance on the saw there. 3 layer huntsman - pretty snazzy!
-
Last mod of 2022, always bugged me how Wenger was in some ways much more innovative than Victorinox. One particular model took me forever to find. The Wenger Double Blade SAK. Finally found one on eBay, but was disappointed in the tool set so I finally made a Victorinox 84 mm Double Blade.


-
@pa_strunk said:
Last mod of 2022, always bugged me how Wenger was in some ways much more innovative than Victorinox. One particular model took me forever to find. The Wenger Double Blade SAK. Finally found one on eBay, but was disappointed in the tool set so I finally made a Victorinox 84 mm Double Blade.Very cool. Looks like a very useful and pocketable knife. The scales are amazing

-
@pa_strunk said:
Last mod of 2022, always bugged me how Wenger was in some ways much more innovative than Victorinox. One particular model took me forever to find. The Wenger Double Blade SAK. Finally found one on eBay, but was disappointed in the tool set so I finally made a Victorinox 84 mm Double Blade.That's great! I was unaware of the Wenger Double Blade until you mentioned it. It looks like it's four layers, but your three-layer setup is even better.
-
My first attempt at an 84mm build using 91mm scissors - the Golfer. Had some very old European stag horn that's was earmarked for the bin during a clean-out. Dates from around the 1930's shot by my grandfather somewhere in Austria. Glad I could repurpose them. I took some photos so will look at doing a separate thread on the build process.
[attach id=0 msg=2390969]
[attach id=1 msg=2390969]

-
Very nice Max, I love how you went with two exposed pins only. The separate thread has been great so far as well.
-
@Enginears said:
Very nice Max, I love how you went with two exposed pins only. The separate thread has been great so far as well.Thank you Enginears

-
-
Nice set,,
JR -
Some lovely mods there - the antler and polished steel both look amazing even though they are about as different as they could be! I’ve just finished a cadet X done the ‘easy’ way with Delemont scissors - like it but have also got a 84mm huntsman small underway which I am attempting with modded 91mm scissors and spring. Not seen that model done on here (although that’s not to say it hasn’t been!) and I think it’ll be a little cracker if it turns out ok. Have had to make some of the liners from brass so a more difficult mod all round than this one…hopefully not to much so for my limited skill set and tool set!!!


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login




