Timberbeast MK2
-

The Timbereast MK2 is now a go!!! It’s not that much different than my original Timerbeast, just cooler. More of what I originally wanted to make, but I botched up a couple of things, the first time around.
The MK2 features a full set of red old cross covers, thanks to Oloha, who kindly donated a set of scales to the cause. He also included two old brass liners, which meant I now had a full set of brass for the mod. I was even able to scrounge up a brass spacer that the keyring attaches to.
I had to take apart a Farmer X for the mod, and an old Electrician that still had a totally unused sheepsfoot blade. So there were tons of pins to drill out. Parts everywhere. One thing I have learned from this experience is that I’m terrible at drilling out pins. Even with a punch to drive in a pilot dimple, and using a drill press, I still manage to screw it up. So both scales survive sometimes, but the occasional scale gets ruined and sent to the grinder. Big kudos to the guys who can perfectly drill out a pin every time.


I originally lined up all the parts, and began assembling, but eventually took the entire knife apart again. There are so many parts, and so many extra parts that look nearly identical to the parts you actually need to use. I quickly learned on my first try at assembly, that I had a couple of wrong pieces. The main blade/awl spring was the wrong thickness. The scavenged electrician also had a small aluminum spacer that went inline with the electrician blade, that looked exactly like the spacer that went inline with the awl, only thinner. Of course I grabbed the wrong one for the mod.Uggghhhh…… But after an hour of fidgeting around, the MK2 was finally assembled.

Notes:
-
I messed up on the original Timberbeast, putting the scissor layer next to the opener/electrician layer, instead putting the wood saw layer there. The knife still works fine, but it is slightly easier to open the scissors on the MK2, with the wood saw layer next to the opener/electrician layer.
-
While the red old cross scales and brass liners look amazing, and are totally to my personal tastes, there is something to be said about the current production scales and liners. The newer components seem to be made with a higher degree of precision, and the scales are made so that the outside tools rub less against the scales. I have one vintage OC scale and one modern scale on my first Timberbeast, as well as modern liners, and the fit is nearly perfect. The only issue is that the scissors don’t forcefully snap closed. With the MK2, full brass liners and two OC scales, you have to be careful when tightening the pivot screws down, and sort of find that balance between tools having a nice snap, and having some lateral play. Even doing my best, the scissors just sort of push closed.
-
I tried my best to use the older version of the cap lifter/screwdriver tool, with the brushed finish and sharper corners, but I just couldn’t make it work. The cap lifter would always rub against the electrician blade. So I eventually had to back up and use the more modern cap lifter. That seems to have more clearance.
As you can see, the MK2 scales are a bit old and banged up in spots. But I really dig the heavily used and vintage look. All I did to clean up the scales and liners was to sand down the worst gouges with wet/dry paper, and use Brasso to clean the liners.
But all in all, I’m super happy with the MK2. It isn’t as much about performance as it is about blending new ideas and a few new parts, with some wonderful old vintage components. It really makes for an interesting knife, with a sensational outdoors-specific toolset. The original Timberbeast will remain as my daily user for now, with the MK2 going into my outdoor pack. I spend approximately 2 months per year living outdoors, so the MK2 is destined to see a ton of hard use in the near future.






-
-
Looks pretty dang good!

-
I like that! -
Awesome!
-
that is a beauty. I like the choices of OC and brass liners, so rugged and elegant at the same time. I am 100% the same on screwing up drilling out the pins sometimes. 
-
I too find drilling out the pins a tricky job….. Great result though!

-
@Enginears said:
that is a beauty. I like the choices of OC and brass liners, so rugged and elegant at the same time. I am 100% the same on screwing up drilling out the pins sometimes. 
@Rizio Il Ghiro said:
I too find drilling out the pins a tricky job….. Great result though!

Thank goodness I'm not the only one. The fact that I'm doing this work at night, in a badly lit garage, with numb hands in the freezing cold, probably isn't helping. What I really need is a dimpling tool with a cup shaped head, to help center that dimple on the pin head. I don't know if such a thing exists, but my dimpler is definitely not the precision tool that I need it to be.
-
Love that. I have more SAKs with that basic toolkit (ie. huntsman) than any other. This is a great take on that though.
I’m another one who often takes out a bushing or nicks a scale when drilling out pins so welcome to the club ;0)
-
Very cool, Buzzbait!
-
Glad that OC SAK went to good use
. Looks great.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login