What Traditional Knife are you toting today?
-
@LoopCutter said:
[attach id=0 msg=2394952]SodBuster Jr Black and simple a GI Jack
Nice knives LC!

-
Everybody's showing out today,,,,,, bravo!
-

Anyone see the Case 2023 vault pattern? Its the Congress. Theres also some nice Damascus coming as well.
-
A 3some todayβ¦
[attach id=0 msg=2395148]
-
Nice trifecta of sharps !

-
Birth year Camillus Demo and a Barehead Trapper


-
Good pairing!

-
Harvester and Mustang

-
Steve - very interesting Cami, if birth year your are just a younginπ. The clippoint must of proceeded the Wharncliff model!
David - your two selections are handsome. Some pretty nice covers on each modelπ
-
Wrong threadπ
-
@LoopCutter said:
A 3some todayβ¦
[attach id=0 msg=2395148]Fine selection of knives LC!

-
Thank you David and Steveβ¦
The 3 selected, actually the 2 Wharncliffe blades was to see if they would work on a project.After visit for treatment was invited to friends house for lunch. His wife is always working some craft project that she sells at fairs and markets. Knew today was fabric patterns.
The material was some faux leather material, less and an 1/8β thick. Patterns were stars, horses, birds in flight, crescent moon, and a Angel wings. These are to be sewn onto sweatshirts.
His wife uses scissors typically, but her arthritis causes difficulty.
The Rough Rider work knife handled the tasks the best. After showing her how to hold and trace the edge of the templates, she was in seventh heaven. I wanted to give them the knife, but NO! He ask where I found it, gave him SMKW and Chicago Knife Work as two outlets.
He ordered 4 from SMKW, two to use and 2 to standby when first ones being sharpen by their son. π
Better than scissors and easy to open!!!
He was also eyeing other models too! I will learn next month how much damage I caused!!!
PS: I wanted to take a picture of her using, but she was not having it as she had a old smock and had no makeupπΉ -
@LoopCutter said:
Thank you David and Steveβ¦
The 3 selected, actually the 2 Wharncliffe blades was to see if they would work on a project.After visit for treatment was invited to friends house for lunch. His wife is always working some craft project that she sells at fairs and markets. Knew today was fabric patterns.
The material was some faux leather material, less and an 1/8β thick. Patterns were stars, horses, birds in flight, crescent moon, and a Angel wings. These are to be sewn onto sweatshirts.
His wife uses scissors typically, but her arthritis causes difficulty.
The Rough Rider work knife handled the tasks the best. After showing her how to hold and trace the edge of the templates, she was in seventh heaven. I wanted to give them the knife, but NO! He ask where I found it, gave him SMKW and Chicago Knife Work as two outlets.
He ordered 4 from SMKW, two to use and 2 to standby when first ones being sharpen by their son. [emoji12]
Better than scissors and easy to open!!!
He was also eyeing other models too! I will learn next month how much damage I caused!!!
PS: I wanted to take a picture of her using, but she was not having it as she had a old smock and had no makeup[emoji257]Nice work LC!

Sent from my iPhone using Tapatalk
-
@LoopCutter said:
Steve - very interesting Cami, if birth year your are just a younginπ. The clippoint must of proceeded the Wharncliff model!Younger than some older than most ;)
Yes, the Clip preceded the Wharn and it's Stainless.
-
Nice carries from awl, and good job by LoopCutter!

Yes, Case is bringing the 68 pattern Congress out of the vault. Many of the members of the other forum I frequent would have preferred a different pattern. But the one shown below catches my eye.

A 3468 CV would be better if they see fit to release one...
-
@LoopCutter said:
Thank you, did not know the clip was stainless.And, you are WISER than your years, regarding traditionals and MTsπ

-
Still have the little Peanut in my pocket today. Decided to do a bit of light whittling while I was walking the dog. Honest.


-
@LoopCutter said:
A 3some todayβ¦
[attach id=0 msg=2395148]Especially love that first one LC.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better π
Register Login