My 3DC
-
It uses a lot less filament and prints faster since there's less volume than yesterday's model, but it doesn't seem to fit the watch quite as well.
Still, it works well, and being a lighter design it fits the Luminox Blackout nicely, since it too is a very light watch, thanks to its carbon fiber case.
Here is the stl:
I'd definitely print/use this one again, even though it seems a bit too small for big, chunky watches. It will hold them well enough, and I don't feel like it is going to fail or anything- it's just an aesthetician thing. Putting a 45mm tuna can type watch on this would make it seem out of place.
Otherwise, it's a nice little stand.
Def


-
You could use a cut-out of MTo's logo. It would save filament and look even cooler.

-
It's on the list, I just need to get a bit better with design software to get there. :D
Def
-
Another enabler.
As soon as you start printing some of them tools and EDC items I'm gonna want one too. I've just got so much stuff, now, that the Boss Lady is starting to protest.
-
Last night I decided to get a bit ambitious and print a Surge Sheath- specifically this horizontal one:
a bit of a caveat here- I don't like hard wallets and I don't like hard sheaths.
That said, I love many tools that I thought were idiotic at first, and I am happy to change my mind about things. I am wrong often, and I'm okay with that.
So, going into this with an open mind, I fired up ye olde 3D printer and banged this one out. The printer did a great job on this one, and the print came out absolutely perfect. I was really impressed with this one and I was really starting to look forward to carrying and using this one.
My first test was a bit of a fail though- I tried quickly found the loop on the print was a bit too small for my belt.

No worries, I have thinner/smaller belts so this isn't a deal breaker.
Def




-
I had read in the description of this STL (and the other Surge sheath I was looking at, also by the same designer) that the sheath was designed with the older Surge in mind, so I dug out my original Surge to see how it fit. Frankly, it looked pretty small for the Surge, so I decided to try the Wave first. The Wave was a bit loose (as expected) but not as loose as I'd think it should be for a much smaller tool in a sheath designed for a Surge.
It didn't fit.
I could only get the Surge in about halfway before it jammed up good.
Trying to put the original Surge in all the way resulted in the sheath breaking.

But, maybe I got it wrong- maybe the designer thought he had an older Surge and maybe it would fit the newer one instead. So, fitting the sheath back together I grabbed the MTO Million Post BO Surge and tried that.
Def




-
Much like the original Surge, inserting the New Surge caused breakage, first in the same position as the original, and then it snapped the little hook off the backside that the base of the handle is supposed to nestle into.
This week I may try increasing it by 5-10% and reprinting, but doing it straight up, this one just doesn't work.
Def


-
I wasn't quite ready to give up on the Surge sheath fail, but I wanted to try something different, so I decided to give the Gerber Belt Clip Holster a shot instead.
Because of the way this one was designed, I needed to add supports, which is basically a thin structure to support bits that stick out that can't be properly printed without something to print on- for example, if you wanted to print a capital letter T, you would need to print supports on either side of the vertical line to support printing the horizontal line.
This means the project uses more filament and takes more time, but as it ensures a better completed project, it's worth it.
I took some pictures during the print so you can see the inner support structure, and the outer "wings" of the sheath. Note that it is also being printed upside down, as that's where the flattest surface is.
Def




-
You will also notice the crosshatch pattern inside the structure. This is to reduce weight, the amount of filament used, and the print time- if one wanted more strength, they could increase the infill percent and use more material, but again, I am starting all of this with recommended settings. I have lots of time to fool around with it later! :D
This one printed at least as perfectly as the Surge sheath, and I as very pleased with the result.
My first test after removing all of the support structures was the belt test, and, unlike the Surge sheath above, this one passed. Not by much mind you, but then I wouldn't want it any looser. It fits well on my belt, as if it was made specifically for it. Apparently the designer wears the same kind of belts I do.
I then grabbed the Multitool.org edition Gerber Pro Scout and was happy to see that, while snug, the ProScout fit in it nicely. I like that it's snug, but at no point did it feel like it was stressing any part.
This is a very well designed sheath, and I'm looking forward to putting a bit of mileage on it. I wore it to the grocery store and it was a bit more comfortable than I imagined it would be.
I'd absolutely print this one again, at least at this point. But, we will see how it manages in actual use. I don't know how easy it is going to be to draw the MP600 when I need it.
One quick note- this won't fit a MultiPlier.
Def




-
Learned some good lessons with those sheaths designs

I like the different designs

I may have some design files somewhere of a bit holder that fit inside a Zippo
need to see if ai can find them and send them if you want 
-
Sure, I'm game!

Def
-
Found them and emailed them to your gmail

-
Got them safe and sound. I will look into them today, and see if I can dig up a Zippo somewhere too!
Def
-
The guy who sent then designed it and had it in a Zippo

It looked really awesome

It is probably for the LM flat bits
I forgot to mention that :ahhh :D -
It may look a bit ugly at first, but with some sanding to get the glue stick residue off it, I think this Apple AirTag MOLLE attachment is quite handy.
It actually has two pieces- the main body as shown in the pics, and a retention ring that keeps the AirTag in it.
The retention ring doesn't seem to actually fit, but that's okay as the AirTag snaps in quite solidly and the strap holders are so tight that the holder won't come loose from the strap without a fight.
If you decide to print this one, don't bother with the retention ring. :D
Def
-
Oops, forgot the pics!

Def


-
Good idea with that holder

-
I like it because you really can't see that there is a tracker hidden inside. My thought is that if i cleaned it up and put a sticker or something on it then no one would think there was an AirTag inside it at all- it would just look like a fancy decorative thing.
I'd thought of also getting a military rank pin or something and mounting it on there, which would encourage the "nothing to see here, just a fancy bauble" type mentality.
Def
-
You could definitely make it blend in on a pack

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login