What Did You Use Your Multitool For Today?
-
Used the pliers on the Kick, to remove the drainage grate, for cleaning.. Yuck... :P
-
Phillips on the KF4 to unscrew the box which houses the toilet in our van... that was a bit yucky too :(
Shame I didn't stop by when passing RP - I couldn't have helped you "store" all those tools while you move :D
Hope it's going ok. -
Used my LM Blast to clip tags off new clothes.
-
Actually used my PowerAssist to de-shell sunflower seeds today, was bored and didn't want to use my teeth. I alway knew compound leverage would come in handy. :D.
Also used it to free the last section on a telescopic fishing rod, which I inadvertantly pulled out to hard and got stuck to the point it wouldn't retract. In this case the compound leverage was a bit much and I did crush the fiberglass section a little.
-
Let my 12 year old son use the saw and knife on the core to cut in smaller sections and bundle some branches i trimmed from a oak tree in my yard.I used a bigger saw,but he was a nice help using the core.Guessing i'm on the lookout for the new supertool 300 for him,keep him out of the toolbox in the garage a lot at the same time too.Bought a new mower with a honda engine for him,shoot,they got to learn to do something besides baseball,girls and video games right?
-
I was going to use the Surge to break up some more old crates out on the farm. Tossed bunch of them into a big pile, yanked one out, threw it up on flat workspace I've sort of set up, opened the wire closures and threw open the lid...
And was greeted by the biggest #&$^@_! wasp's nest I've ever seen in my life. Populated by the #&^@_! biggest wasps I've ever ran across...
I now have a sort of insight into what it's like to set off a booby trap. :ahhh
I managed, by some higher grace, to walk away (or run swearing away) unstung. Not for lack of trying on the wasp's part, mind you.
Needless to say, the Surge didn't get to do any work today. I think I will return tomorrow equipped with a touch of WMD to deal with this situation. (Code Name: Operation Black Flag...) >:D
-
the trusty spirit PE blade broke down some 4x12" wallboards for the trash container. later, it drove a phillips screw into a door hinge that the flooring contractors lost and pounded in a hinge pin for another door they so thoughtfully forgot to put back.
i love my spirit.
-
Used the wave to repair some burned 8 AWG wire. Was able to cut the wire with no problems, but trying to strip it with the wave was problematic due to the waves offset cutting blades and thickness of the wire. Instead of climbing off the roof, I used the straight edge blade to strip the insulation, which worked quite well.
-
@Blackbeard said:
Used the wave to repair some burned 8 AWG wire. Was able to cut the wire with no problems, but trying to strip it with the wave was problematic due to the waves offset cutting blades and thickness of the wire. Instead of climbing off the roof, I used the straight edge blade to strip the insulation, which worked quite well.A lotta times, I'll run the blade around the insulation, then put the needle nose in the tip of the insulation and pull it off like a sock.
-
crossgrip
taking some staples out
10/10 :D
-
Used my SAK Ranger to cut up half a ton of cardboard.
Needs a few minutes with the Sharpmaker now :D
-
-
Referencing my last post... Operation Black Flag was carried out at c.1500 hours local time...
The Surge was then used to remove the primary target to another location, where the Burn Notice Protocol was carried out.
All Operations were carried out successfully, and with no friendly casualties.
(Those were the biggest freaking wasps I've ever ran across... :o Yeesh...)
-
repaired some wire backed silt fencing damaged by a lumber truck. basically light rod busting. no problem
-
@HBlaine said:
Referencing my last post... Operation Black Flag was carried out at c.1500 hours local time...The Surge was then used to remove the primary target to another location, where the Burn Notice Protocol was carried out.
All Operations were carried out successfully, and with no friendly casualties.
(Those were the biggest freaking wasps I've ever ran across... :o Yeesh...)
Congratulations on a successful mission

-
I didn't want to rummage around the shed tonight for one of those wheel thingys you use to put a window screen in the metal frame. So I used the back of the can opener of my LM Pulse. Worked like a charm.
-
Stripping some flex today with my CT 41 it works great for flex,coax or twin and earth
using the main blade,small one open and out of the way.all you do is rotate the cable you want to strip toward the tang,use only the blades spring pressure for this purpose,with practice you can do away with some other wire strippers that can either not be at hand or through experience you've loaned it out and it's GONE :ahhh

-
Nice tip, John

-
posted in other place, but i guess is better here:
crunch as a multi size bit adapter:

10/10

-
igniter for the grill died today so the spirit was put to good use as a nice long handle for poking a match in, worked a treat

10/10
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login