Home solution for loose pliers pivot! Experiment!
-
For the record I did put the tool itself outside of the edge of the table and put only the plierhead/scissorhead on the table to prevent ut all from bending. Just a small warning if anyone tries this :D
-
Btw, is there a way to do this to a OHT?
The ONLY Leatherman I ever had real play in the pliers is with an OHT that I sent back.
All the others might have been looser in the action than I like, but no play.Anyone tried something to fix the OHT pliers? :)
-
@aikon2014 said:
Btw, is there a way to do this to a OHT?
The ONLY Leatherman I ever had real play in the pliers is with an OHT that I sent back.
All the others might have been looser in the action than I like, but no play.Anyone tried something to fix the OHT pliers? :)
I did. The turning method didn't work on OHT pliers. The pivot is extremely tough. U can hit it pretty hard with the peening method with very little visible scarring. But from factory, most OHT I have seen have some form of misalignment at the tip. I have never seen one thats perfect before.
-
@Sam Lim said:
Btw, is there a way to do this to a OHT?
The ONLY Leatherman I ever had real play in the pliers is with an OHT that I sent back.
All the others might have been looser in the action than I like, but no play.Anyone tried something to fix the OHT pliers? :)
I did. The turning method didn't work on OHT pliers. The pivot is extremely tough. U can hit it pretty hard with the peening method with very little visible scarring. But from factory, most OHT I have seen have some form of misalignment at the tip. I have never seen one thats perfect before.
It's such a shame :( I would love to have a single hand tool for fishing situations, but no dice with the OHT :(
-
@Sam Lim said:
Btw, is there a way to do this to a OHT?
The ONLY Leatherman I ever had real play in the pliers is with an OHT that I sent back.
All the others might have been looser in the action than I like, but no play.Anyone tried something to fix the OHT pliers? :)
I did. The turning method didn't work on OHT pliers. The pivot is extremely tough. U can hit it pretty hard with the peening method with very little visible scarring. But from factory, most OHT I have seen have some form of misalignment at the tip. I have never seen one thats perfect before.
It's such a shame :( I would love to have a single hand tool for fishing situations, but no dice with the OHT :(
Well most still grip and cut without any noticeable problems. So I think it's still a good tool.
-
Some discussion about it here: /post/1575499
-
I just did the method on my new Juice S2, interesting enough, I had to turn it counter clockwise, unlike the Rebars and Wave's which I did clockwise to tighten.
I first tried to do clockwise with the Juice, and it loosened, so I reversed it and it tightened. I wonder why. I had the non "rotating" surface up on all the tools while doing this. -
Sam Lim have the fix of the pliers kept and worked in the long run for you? I haven't tried mine for long enough to be able to tell.
-
@aikon2014 said:
Sam Lim have the fix of the pliers kept and worked in the long run for you? I haven't tried mine for long enough to be able to tell.To be very honest, me neither... But so far it held up.
-
Hope it's OK to ressurect this thread but I gave this a twirl, pun intended, and it worked.
I used my crunch to do it to a pst which had a slight but perceptible wobble on.
20 degrees counter clockwise was enough to bind the plier, 10 degrees was just so and has the wire snips cutting paper like our Tim demonstrates post nail cutting extravaganza on his charge.
You can see the brushed lines show the rotation and yes I did mar the pliers, the crunch wouldn't turn it unless it got a bite on it.
Previously I used the ball pien method but this is better imo. Deffo worth doing.
-
Awesome that this worked out for you, ed

-
It is worth a little marring to have the pliers working well again. Good job

-
Thanks Poncho and Adam, yea I have ocd issues with plier slop and if the wire cutter doesn't cut paper I usually pull out the hammer, but this is far better.
I don't mind the bite mark on this tool, it's a hard user but will investigate using copper washers something? -
@ed_is_dead said:
Hope it's OK to ressurect this thread but I gave this a twirl, pun intended, and it worked.
I used my crunch to do it to a pst which had a slight but perceptible wobble on.
20 degrees counter clockwise was enough to bind the plier, 10 degrees was just so and has the wire snips cutting paper like our Tim demonstrates post nail cutting extravaganza on his charge.
You can see the brushed lines show the rotation and yes I did mar the pliers, the crunch wouldn't turn it unless it got a bite on it.
Previously I used the ball pien method but this is better imo. Deffo worth doing.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login