GOAT Tools Owners Club
-
Center axis universal bit driver works well with ratchet driver.

-
I’ll be following this and I’m interested to see what you all think. I am still not sure about it.
Anyone try the “hammer” function yet? Pretty sure that’s the point of the flattened handle ends, right?
-

Yes I have used the hammer, and I like it. However, hammering in a horizontal orientation shakes the bit loose from the bit driver. I thought perhaps a bit with a ball detent would help, but that shakes loose also.
The magnet that is used to retain the bit in the bit holder does not exert much force on the bit

Before hammering

After hammering

-
@pa_strunk said:
Center axis universal bit driver works well with ratchet driver.
-
My scissor spring has a tendency to pop out of place, no doubt aided by a bit too much rounding over at the edge of the scissor handle:


Otherwise, the scissors seem to cut fine.
By the way, that would be the remnants of my lunch that you see on my leg

-
The Leatherman ratchet and bits sit deeper than regular size quarter inch bits. I can turn it upside down and shake it without loosing Leatherman bits, ratchet, or regular quarter inch bits.


-
A visual comparison with the Free P4:


GOAT pliers are spring-loaded, Free P4 are not
I swapped in the S35vn blade this morning
The hot swap feature seems to work great. I am a little clumsy with it, but I am sure swapping out tools would go quickly with a little practice.
The only removeable tool that I don't like is the file. It is of the same quality as what is found in many Chinese MTs. I may make a file to take its place.
-
It seems that so much thought and attention was spent on the handles that the pliers became somewhat of an afterthought.

The Free P4 was able to easily cut 8 awg THHN copper, 10 awg THHN copper, 14/2 Romex, and bare 14 awg copper.
The GOAT MT could not. There are two reasons why:
-
Both MTs have bypass cutters. Bypass cutters cut by way of shearing force. However, many bypass cutters taper to an edge. This allows the cutter to indent and wedge apart the material (as anvil cutters do), aiding the shearing action. The Free P4 replaceable cutters are made in this manner. The GOAT replaceable cutters are flat and have to rely almost totally on shearing forces.
-
Since the cutters rely on shearing, there must be enough room for the material to move past the cutters. The GOAT does not have enough room for the material to move and so the material prevents the jaws from closing all the way.
GOAT


P4


I was able to cut 16 awg soft steel wire, but not easily. Given that this MT is billed as "Gear Of All Trades", this is a major flaw that should be corrected going forward.
-
-
Glad to see it going theough it's paces
Hopefully that is something that can be remedied either on later models or with a redesign of the removable cutters 
-
Thanks for the comparison, Adam. I am very interested in how this will perform. Too bad about the cutters. Certainly an issue that should be looked at.

-
Thanks guys

It does take a great picture


-
it’s a very cool looking MT 8) -
Is there a website for the GOAT?
-
-
I've gone to this page but there is no place to buy the tool. When I click on "Shop". I get a 404 error
-
You can’t buy them yet - only sign up to the newsletter.
Only those that backed the kickstarter are getting them currently,.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login





