GOAT Tools Owners Club
-
I've gone to this page but there is no place to buy the tool. When I click on "Shop". I get a 404 error
-
You can’t buy them yet - only sign up to the newsletter.
Only those that backed the kickstarter are getting them currently,.
-
First impressions, just on the basis of the standard implement loadout (this may echo those of some others, I guess; will try exchange implements this weekend):
A tad smaller and lighter than I expected. Seems well enough made, with the following small issues:- Scissor spring sometimes slides off its abutment surface when operated. (I have an idea how to solve that through judicious application of a file.)
- Opening tools requires getting used to, and tends to cause release lever to open as well. One trick is to keep this closed with whatever fingers are free at the time.
- Sheath has two elastic side pockets - alas with an open bottom, so maybe only good for things having clips - and one belt side pocket which will fit some spare implements, although the long ones stick out at the top and will inhibit tight closing of the lid flap.
-
I'm beginning to like the hot swap feature. This works really well, if you keep in mind which way of inserting the tool is the correct one. The pic below shows how.
The scalpel blade holder is really nice. I need to buy spare blades though. Can anyone identify the type of fitting?
I had bought the file as an extra and have briefly tried it out. As someone remarked above, it is not quite as bad as some, but by far not as good as some others
. The wide cross-cut and narrow sides do a reasonable job. The wide diagonal-cut side could use rather a bit of improvement.OHO main blades seems to work, kind of (if you manage to avoid the release handle and ignore tool clumping) but I have yet to find a good way to OHC...
-
Curious to hear more as y'all use the GOAT more. Bummer about the file. I have alway liked LM diamond file. I can see how the scissor spring ( thanks to pics ) pops out. Does seem like a fix that owner can do
. I don't cut much wire but I can see how it can be bothersome for this tool not to be able to cut. -
On the wire cutter:
- on my pliers the cutter inserts were loose and had to be tightened, and now they rub slightly when closed denoting better contact between the cutting surfaces.
- however, even so, the blunt insert edges don't cut but only shear off (as noted somewhere above) causing pinching in the too small space afforded and mediocre cutting at best. Insulated wire tends to have its insulation pinched, not cut (if you're lucky you'll cut the metal core though).
-
I've taken a closer look at the wire cutter inserts. I had bought a package of spare ones too.
I was wondering if one could grind an angle into the sides straightening the current two-faced sides into a single face, thereby making the cutting edge say 75-80 degrees instead of 90.
If one did, would that destroy the tempering, assuming one exists on stock inserts?
-
Re wire cutter inserts, again:
When I looked at the spare ones I bought I thought the cutting edge was narrower than that of the ones mounted to the pliers out of the box. Close comparison confirms that, see top pic (spare on top), I'm guessing the cutting edge on the spare is about 60% of that of the original.
So I exchanged the inserts. Slightly better in that the cutter can now cut chicken wire, with a bit of wringing as clearance has remained the same. I think I might subject the originals to some grinding experiments.
This, because meanwhile, compared to the P4 as my impromptu chicken wire cutting benchmark, the spare cutters still have a wider edge, see bottom pic...


-
OK, so I ground down one face each of the original inserts to a narrow edge, see first pic. Just slightly better.
Problem remains the lack of clearance between insert (held by a fattish screw) and the opposing pliers wall, and what looks like a slightly convex surface of the latter, see second pic. I think one could in theory take a file to that face but I hesitate.


-
Spring loaded pliers are not only an advantage, see pic showing how I just found it... [attach id=0 msg=2433006]
Edit to add: as a nice touch, one of the tool's standard implements is a 2mm Allen key doubling as a lanyard ring and which by the nature of the tool is detachable. This can be used to tighten pivots and exchange wire cutter inserts. Tightening the plier pivots was what was needed to inhibit the auto-spread feature.

-
@Adam5 said:
My scissor spring has a tendency to pop out of place, no doubt aided by a bit too much rounding over at the edge of the scissor handle:

Otherwise, the scissors seem to cut fine.
By the way, that would be the remnants of my lunch that you see on my leg

I had the same problem. I used a small Dremel to square off the cross section of the end of the spring (this was slightly rounded off) and bent it slightly into the plane of the scissors tool side half. That seems to have helped.
The scissors themselves cut very well and open wide, much wider than e.g. on a Spirit.
-
I will be doing the same adjustments to
night or tomorrow. I contacted GOAT Tools a few days ago and Michael O'Donnell said that if the adjustments don't work or if the spring broke while trying to bend it then he would take care of the warranty.I am hesistant to modify the plier head to improve the cutting of thicker materials unless I am sure I can get a replacement. I am not sure I will be using it with any regularity, so there may be no reason for me to mod it.
I do plan to contact GOAT Tools about the problem in order to give feedback.
-
Excellent Adam5. If you have a direct line you might add my experience with the wire cutters. I think (after comparing with my Free P4) that it's rather a lack of clearance to the off side of the cutter insert which causes the pinching - should this not occur the cut items would be ablo to fall free (up to a certain size, obviously).
The very slight scissors mod seems to be holding up, so can heartily recommend. Unless you're really ham fisted I don't estimate there is an increased risk of breaking the spring. Use two sets of flat pliers close to where the spring becomes narrow and apply very measured force.
Otherwise I am rather impressed for a first time product, although I have yet to put it through its paces in earnest.
-
Has anyone in Europe gotten their multitool yet? Of so, who shipped your order and did you get an email from GOAT when they shipped?
-
Yes, DHL and yes (Germany)

-
@Dutch_Tooler said:
Yes, DHL and yes (Germany)
Sounds promising! I guess I'll just have to wait. I didn't back them Om indiegogo until early January so I guess I'm a bit further down on the list..
-
@Herman Axtelius said:
Sounds promising! I guess I'll just have to wait. I didn't back them Om indiegogo until early January so I guess I'm a bit further down on the list..I got mine late last month and I'd backed them on Kickstarter a couple of years ago. I know we're not part of the EU anymore ::) but mine arrived quite quickly once I got the shipping email

It was sent by DHL but delivered by Hermes here in the UK

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login







