What Did You Use Your Multitool For Today?
-
@Screwtape said:
igniter for the grill died today so the spirit was put to good use as a nice long handle for poking a match in, worked a treat
10/10
Did you not think of the potassium + glycerin tea bags :D
-
-
@cliosguy said:
posted in other place, but i guess is better here:crunch as a multi size bit adapter:

10/10

OK, being picky here as I am in a picky mood. :P
How can you say that is 10/10? Not exactly the easiest to use is it? A dedicated extra comfy to use bit driver would be my 10/10 but that?
I've finished being picky now. :D
-
Good shift at work then Ben? :D
-
posted in other place, but i guess is better here:
crunch as a multi size bit adapter:

10/10

OK, being picky here as I am in a picky mood. :P
How can you say that is 10/10? Not exactly the easiest to use is it? A dedicated extra comfy to use bit driver would be my 10/10 but that?
I've finished being picky now. :D
thats the problem it solved...i didnt have a "dedicated extra comfy" :P
-
Resurrection:
So, on Fri (I think) I created the OH Locksmith. Sat morning, Mrs. Whippy and I began work demolishing a wall damaged by water and replacing it with 2 windows and reframing. The damage went up to the roof line. Finished Sunday evening.
Used the OH Locksmith extensively as a keyhole saw, to file through nails before snapping them off with a hammer in the old exterior sheathing and the mainblade for trimming the plastic flashing around the new windows. Ended up with a few scars on the scales, and needed to sharpen the main blade, but overall, I'd rate it 8/10 as utility tool.
BTW, I used a Husky box cutter to score drywall, rather than the mainblade. Just seemed to be the right way to go.
-
Good call on not using the SAK for the drywall, that stuff really dulls any knife in seconds.
-
Cut the tip off of a hypodermic needle. 8)
-
Used the Vic Spirit to strip down a Mac 700 Spot to day as the power modual didn't seem to be working. The ratched set was perfect not only by having all the torx and allen heads necessary but also being able to get into all the awkward bolts where a long handle driver wouldn't reach

Spirit 10/10
Unfortunately the power module was a bit further gone than I expected as when I swapped it into a different unit to prove the fault it exploded, :-\ violently causing an as yet unknow amount of damage that I will be investigating tomorrow :-X
My skills 1/10 :-[
-
crossgrip flat driver as a mini prybar to open a wall faceplate 10/10 :D
-
@Screwtape said:
Used the Vic Spirit to strip down a Mac 700 Spot to day as the power modual didn't seem to be working. The ratched set was perfect not only by having all the torx and allen heads necessary but also being able to get into all the awkward bolts where a long handle driver wouldn't reach
Spirit 10/10
Unfortunately the power module was a bit further gone than I expected as when I swapped it into a different unit to prove the fault it exploded, :-\ violently causing an as yet unknow amount of damage that I will be investigating tomorrow :-X
My skills 1/10 :-[
That's a funky looking bit of kit. I think if I came across it above a darkened auditorium I'd ask if it wanted to be taken to my leader :ahhh ;)
-
@Screwtape said:
Used the Vic Spirit to strip down a Mac 700 Spot to day as the power modual didn't seem to be working. The ratched set was perfect not only by having all the torx and allen heads necessary but also being able to get into all the awkward bolts where a long handle driver wouldn't reach
Spirit 10/10
Unfortunately the power module was a bit further gone than I expected as when I swapped it into a different unit to prove the fault it exploded, :-\ violently causing an as yet unknown amount of damage that I will be investigating tomorrow :-X
My skills 1/10 :-[
I hope it's not as bad as it sounds. :-\
-
nothing flashy but i used the spirit PE blade to cut the end off a tube of fire caulk to seal an electrical penetration to pass a rough inspection.
later i used the SE blade to shorten the disconnect rope for 2 garage doors on another home. both blades did very well. i am not carring a SAK lately to force myself to use the spirit wherever possible. no complaints so far. -
@Neil said:
That's a funky looking bit of kit. I think if I came across it above a darkened auditorium I'd ask if it wanted to be taken to my leader :ahhh ;)You should see the bits all spread out, I'll try and get a pic before a reassemble it tomorrow
I'm an optimist about the 2 year warranty ;) hope it covers idiots with multis

-
I am doing a lot of decorating ATM and moving stuff around. The Fuse has been pushed pretty hard, but is still going strong.

-
Used the Wave to finish tearing up crates, etc., to feed the nice big fire I had going in the improvised burn cage I put together. (Another Wave project.)
Alas, no pictures. I didn't have time, as I didn't have the help that I thought I would....

As the man said, "...You have to do everything yourself... It's a funny world we live in..."

-
Went to the range to shoot my black powder rifle at today. Used my Spartan to cut my shooting patches at the muzzle did a great job. Had a good time. Getting ready to go night fishing for Catfish right now. Hopefully i will have some fish to clean. I love catfish and eggs in the morning.
Mike -
What do you use for bait?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login