Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Executive mod question

Scheduled Pinned Locked Moved Swiss Army Knights Forum
9 Posts 1 Posters 1.2k Views
  1. Home
  2. Tool Talk
  3. Swiss Army Knights Forum
  4. Executive mod question
Executive mod question
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • psyjohn Offline
    psyjohn
    Posts: 543
    psyjohn Offline
    psyjohn
    wrote on last edited by
    Quote Reply

      I have been trying to mod an Executive to add a 58mm combo tool, but I'm stymied on how to get the tools to fit. The combo tool works opposite the main blade, but I can't figure out a way to fit the other tools in. If I put the scissors opposite the file and orange peeler the two combined springs are just a bit thicker than the scissor spring. The difference is enough to mess up the action when opening and closing the tools, but it's not enough to add a spacer. Has anyone done such a mod or seen one done? I tried to search here without any luck. Also tried Reddit, as I think I saw one once, but no luck searching there either.

      1 Reply Last reply
      • Barry Rowland Offline
        Barry Rowland
        Posts: 31,387
        Barry Rowland Offline
        Barry Rowland
        wrote on last edited by
        #1 Quote Reply

          I would try in the Modders section of the Forum. You might get a faster answer there.
          https://forum.multitool.org/index.php/board,16.0.html

          1 Reply Last reply
          • IMR4198 Offline
            IMR4198
            Posts: 6,451
            IMR4198 Offline
            IMR4198
            wrote on last edited by
            #2 Quote Reply

              I sure am glad that Barry replied to your question. It bothers me a little when nobody says anything. I was going to tell you all about the tool spacing, and tolerances. The short comings of various spring values and proper fitting of the combo thingy. But Barry saved me the trouble.
              Naturally I would have had to make up everything, because I don't know any of the answers to your questions. That wouldn't have stopped me from answering though. I never has so far. Some of the modders here know about everything. Best wishes. Gary (IMR)
              :facepalm:

              1 Reply Last reply
              • pa_strunk Offline
                pa_strunk
                Posts: 1,823
                pa_strunk Offline
                pa_strunk
                wrote on last edited by
                #3 Quote Reply

                  Hey there, just saw this post. Easiest way to place a 58 mm combo tool into an executive is to place the combo tool and scissors on the same side. Have the large and small blades opposite the scissors. Place the file (on outer edge) and orange peeler (in the middle) opposite of the combo tool. Take a look at link below and let me know if you have any questions. Look forward to seeing what you come up with.

                  /post/2347929

                  1 Reply Last reply
                  • psyjohn Offline
                    psyjohn
                    Posts: 543
                    psyjohn Offline
                    psyjohn
                    wrote on last edited by
                    #4 Quote Reply

                      @pa_strunk said:
                      Have the large and small blades opposite the scissors. Place the file (on outer edge) and orange peeler (in the middle) opposite of the combo tool.

                      :like:

                      Thank you!

                      1 Reply Last reply
                      • PitCarver Offline
                        PitCarver
                        Posts: 3,025
                        PitCarver Offline
                        PitCarver
                        wrote on last edited by
                        #5 Quote Reply

                          @pa_strunk said:
                          Hey there, just saw this post. Easiest way to place a 58 mm combo tool into an executive is to place the combo tool and scissors on the same side. Have the large and small blades opposite the scissors. Place the file (on outer edge) and orange peeler (in the middle) opposite of the combo tool. Take a look at link below and let me know if you have any questions. Look forward to seeing what you come up with.

                          /post/2347929

                          Now, I'm gonna have to try too.

                          1 Reply Last reply
                          • ComboTool Offline
                            ComboTool
                            Posts: 437
                            ComboTool Offline
                            ComboTool
                            wrote on last edited by
                            #6 Quote Reply

                              I've done a similar mod (with a 65mm combo tool) and I used slim washers (can't remember if they were 0.1 or 0.2 mm) to compensate for the thickness difference between one wide spring and two narrow springs.

                              1 Reply Last reply
                              • psyjohn Offline
                                psyjohn
                                Posts: 543
                                psyjohn Offline
                                psyjohn
                                wrote on last edited by
                                #7 Quote Reply

                                  Well, I've decided to give up on this idea entirely. For one thing, there's something about the pins on a 74mm. I've modded 91, 84, and 58 mm knives without a problem, but on a 74 the pins bend with even light taps with a 4oz hammer. I assembled the mod today but nothing lines up right. Two tools on the same pin are too tight and too loose. The scales won't fit. I mod knives as a relaxing hobby and the 25 times I've tried to make this work have been the complete opposite of relaxing. Thank you for the advice but this is a knife that isn't meant to be.

                                  On to the next project...

                                  1 Reply Last reply
                                  • pfrsantos Offline
                                    pfrsantos
                                    Posts: 24,165
                                    pfrsantos Offline
                                    pfrsantos
                                    wrote on last edited by
                                    #8 Quote Reply

                                      @psyjohn said:
                                      Well, I've decided to give up on this idea entirely. For one thing, there's something about the pins on a 74mm. I've modded 91, 84, and 58 mm knives without a problem, but on a 74 the pins bend with even light taps with a 4oz hammer. I assembled the mod today but nothing lines up right. Two tools on the same pin are too tight and too loose. The scales won't fit. I mod knives as a relaxing hobby and the 25 times I've tried to make this work have been the complete opposite of relaxing. Thank you for the advice but this is a knife that isn't meant to be.

                                      On to the next project...

                                      :worthless:

                                      :popcorn: :popcorn:

                                      1 Reply Last reply

                                      Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                      Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                      With your input, this post could be even better 💗

                                      Register Login

                                      1. Home
                                      2. Tool Talk
                                      3. Swiss Army Knights Forum
                                      4. Executive mod question
                                      Reply
                                      • Reply as topic
                                      Log in to reply
                                      COMMUNITY LINKS
                                      EDC-TV SAKWiki GearFeed SAKSelector
                                      Operational Funds

                                      Help us keep the Unworkable working!

                                      Make A Donation
                                      November Goal: $300.00
                                      Due Date: Nov 30
                                      Total Receipts: $0.00
                                      Below Goal: $300.00
                                      0% funded
                                      • Login

                                      • Don't have an account? Register

                                      • Login or register to search.
                                      • First post
                                        Last post
                                      0