New Volty Bit: THE SWITCH.
-
@Grand_Banana said:
I’m running into this situation below:[attach id=0 msg=2439749]
Doesn’t rest fully closed in the vertical, but doesn’t seem to be in the way horizontal. Doesn’t appear any way to reshape. As far as I can tell the pin on my Wave is not bent.
Don’t attempt to reshape the bit, if you mar the surface you won’t be able to make a connection on that side. I found that slightly bending the pliers stop works fine with no affect on my tools.
-
Mine arrived.
I'm very happy with it. I included a few pics/mini review.I used it to check battery voltages and alternator output. Both were the same as my multimeter.
The body mode for fuse checking is a great feature for side of the road where fuse access is hampered by poor access and the lack of a long nose pliers.
Checks out for spark plug leads too. Haven't check temp function yet.If you intend using this in tti charge the bit driver fouls the pliers stop and prevents you closing the tool fully.
<a href="https://ibb.co/DV76k4h" target="_blank" rel="noopener noreferrer"><img src="https://i.ibb.co/xCMcGhW/20230927-125118.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>So a wee rip with a dremel and diamond burr bit to take a mm off the stop and alls good. Just bear in mind the pliers will still contact it so don't torque down the handles detent against it when closing. What I did was ensure the weaker handle detent was acting on it, that way when I torqued the tool closed the pliers was in the other handle Hope that makes sense.
<a href="https://ibb.co/PjDm0B6" target="_blank" rel="noopener noreferrer"><img src="https://i.ibb.co/sRWmzLV/20230927-131214.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
<a href="https://ibb.co/9ZvkTjx" target="_blank" rel="noopener noreferrer"><img src="https://i.ibb.co/5K9g8VQ/20230927-132233.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Here it is used as intended with the micro bit driver as the negative.<a href="https://ibb.co/Ld2WsJh" target="_blank" rel="noopener noreferrer"><img src="https://i.ibb.co/60fxq1J/20230927-131517.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
In use. Handily it repeats the test as long as she's hooked up.<a href="https://ibb.co/LnmvjBZ" target="_blank" rel="noopener noreferrer"><img src="https://i.ibb.co/t8g3jnJ/20230927-134320.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Unnoticeable on the keys, missus says it looks like a lippy haha. A foot length of small gauge wire with a tiny croc clip soldered on in your back pocket and your good to go.Great product PCPOODLE, I have shown this elsewhere and there's a few sales inbound.
Can I ask whats the situation re water, can it get wet?
Your idea of supplying with a clip and wire is great. -
Thanks everyone for sharing pictures.
I am doing a "Water Resistance Test". I'm thinking total submersion in tap water for 5 minutes. Would this be enough to call it water resistant in your eyes? The internal contacts of the power switch are gold plated but some current will flow and slowly degrade them even if the switch is off. I'll start the test tonight and post results.
As far as some of the fitment issues go, I have an updated version of the switch coming soon that is 3mm shorter without losing any features. This should allow fitment into the new ARC and hopefully the rest of leatherman's product line.
One last thing, I have a prototype in progress that has a magnetic sensor for finding drill hole paths. Let's say you need to drill a hole in a wall or through a ceiling, you can use this proposed feature to scan the wall until you find the magnet on the other side for correct drill placement. I'm testing it with one of those magnet based stud finders and can successfully locate it through 12" of wall. Does this feature interest anyone?
[attach id=0 msg=2444202]

-
@pcdoodle said:
Thanks everyone for sharing pictures.I am doing a "Water Resistance Test". I'm thinking total submersion in tap water for 5 minutes. Would this be enough to call it water resistant in your eyes? The internal contacts of the power switch are gold plated but some current will flow and slowly degrade them even if the switch is off. I'll start the test tonight and post results.
As far as some of the fitment issues go, I have an updated version of the switch coming soon that is 3mm shorter without losing any features. This should allow fitment into the new ARC and hopefully the rest of leatherman's product line.
One last thing, I have a prototype in progress that has a magnetic sensor for finding drill hole paths. Let's say you need to drill a hole in a wall or through a ceiling, you can use this proposed feature to scan the wall until you find the magnet on the other side for correct drill placement. I'm testing it with one of those magnet based stud finders and can successfully locate it through 12" of wall. Does this feature interest anyone?
[attach id=0 msg=2444202]
That's brilliant news Pcdoodle, so it's at somewhere between ipx-5 and 7 as is then. On another site where I showed it techy heads suggested not getting it wet so I have it on my keys in a small titanium cylindrical capsule but I'll revert back to the lippy so.
The improved features would be a great addition. I have already used it to fault find a fuse board in body mode and on cr2032 cells I had lieing around of unknown charge. Such a great thing to have and forget you have to all of a sudden remember you have it and use it! If that makes sense l
-
Results: Volty Switch is not only water resistant but waterproof. I left it submerged in the cup 12 hours while powered on and 12 hours while powered off and it still works great. I'll keep a long term test going.
I placed an order for the ARC today, I will follow up on fitment. The new shorter version in the picture is what we are shipping now, hope it fits them all!
[attach id=0 msg=2444486]

-
That is awesome
love seeing the feedback from here getting put into this

-
Ordered yesterday after discovering this!
I’m wondering if the spacing between contacts is short enough that the volty switch could just be held against a 9 volt (probably using a single 3d printed part) battery for charging.
Once I get mine I’ll definitely investigate some small form factor charging options.
-
Great news pcdoodle. -
Good news, I got the ARC in and Volty Switch Update Fits.
The ARC is also a fantastic tool, it will be my new daily.




-
I'm seeing lots of QC complaints about the ARC on that one website everyone loves to hate, I've been carrying mine everyday. Happy to say after driving mine for 1 week, I have no complaints.
The holes for the belt clip on the other side looked rather lonely, so here's a small flashlight prototype I made on the laser cutter: dual LED so if can also illuminate the screwdriver end too.
[attach id=0 msg=2446278]

-
@pcdoodle said:
I'm seeing lots of QC complaints about the ARC on that one website everyone loves to hate, I've been carrying mine everyday. Happy to say after driving mine for 1 week, I have no complaints.The holes for the belt clip on the other side looked rather lonely, so here's a small flashlight prototype I made on the laser cutter: dual LED so if can also illuminate the screwdriver end too.
[attach id=0 msg=2446278]
Will be in line to buy the torch when it drops

Very concerning regards the obvious lack of a qc for this tools launch. Absolute disgrace that tools are being shipped the way they are, very damaging to the brand imo. -
Since I got the ZapWizard's Garage #5 Ratchet Sheath, went ahead and ordered the Switch to carry on the sheath's side. Seems like a clever gadget with a rechargeable battery on board.
-
@pcdoodle said:
I'm seeing lots of QC complaints about the ARC on that one website everyone loves to hate, I've been carrying mine everyday. Happy to say after driving mine for 1 week, I have no complaints.The holes for the belt clip on the other side looked rather lonely, so here's a small flashlight prototype I made on the laser cutter: dual LED so if can also illuminate the screwdriver end too.
[attach id=0 msg=2446278]
How is this powered? Am assuming like the newer Volty version with the battery?
What is a good way of charging that itty bitty Volty battery? Mine arrived yesterday. Not done much other than testing some 18650 batteries. Thought they would of been more powerful that 4.1 volts. Use them in Sofern & RovyVon flashlights.
The bit was tight for my older Charge TTi (version 1.0). Have not used in the 40th Anv G#5 yet. This is supposed to fit in ZapWizard's Garage #5 holster, probably without the rubber shroud?
-
Oh, and the manual gets slightly confusing on switching to different mode.
When it says to reboot, how exactly is that done??Hmm. Did not know there was a switch. :D
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
-
Had carried the Volty+ in a bit slot on a Zap Wizard sheath up until I went to get it and it was missing. Later I ordered another Volty+ and tried the keychain carry, but I carry too many keys and lost the plastic cover. Anymore I carry the Volty+ inside the Garage #5 bit slot, but that leaves me without a philips/standard bit. 🤔 What to do...
Wonder if there is a way to carry the Volty+ inside the seath side with a slim vertically stored bit card of some sort. Not seen one anywhere online.
Anyhow, the Volty+ fits right into the Garage #5 bit slot perfectly. Slides right in behind the L keeper.
PS: Did find the first Volty+ and gave it to Kip on the TOT (Trikes on Tour) rally in Kellogg Idaho. Had a feeling he might find it useful. Did not really need two of these gadgets, so why not pass it on? :D


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login