ARC Owners Club
-
I've posted this picture in a few places already but it's my favorite. I used a small tesla coil and a long exposure. No photoshop needed.

-
Fantastic, sir.

-
Seen it in a few places but it never gets old, buddy

-
I’ll apply. So far I really like the Arc. In fact, This and the Skeletool CX are my favorites now.
[attach id=0 msg=2445593]

-
Congrats gman
Great pic 
-
-
Great news, cynan
and congrats on getting one

-
Pleased to say that the bit driver holds the bit much more secure than the #005.
Same here. Just arrived from Portland a day earlier than expected, and I’m also relieved that the bits are more securely held.
Going to give it a try for a few weeks to see if it will replace my P2 and P4 as my favourite daily carry.
[attach id=0 msg=2445624]

-
-
Great pics Crunchie and pa

Love that setup as well, pa

-
-
Where can that sheath be purchased
-
-
Waiting to see what y'all will be using for sheaths. I did have a leather one crafted, and asked the crafters to offset the snaps to one side due to the belt clip. They did not set it over far enough to my liking. Going to look the sheath over to see if I can cut out some material in the back for the clip to slide into, leaving the snaps cover without the clip as an obstruction.
Tempted to put some sort of band over it cause I would be really smurfed if I lost the 40th Anniversary / Garage #5.
-
@cdcengineer said:
Where can that sheath be purchasedHe is right that sheath is a Zapwizard special. I have bought several of his items. All have been durable and worked flawlessly.
-
@ajcrean said:
Ooo! Can I submit my application for the ARC Owners Club? My two new purchases:
Manufacturing stamps on my ARC are 0423/0423. Surprised to see they were assembling these six months prior to release date but am very happy to own one.
If they are both new which one are you gravitating to more. I have a charge tti I love and a wave. Not handled an Arc yet.
-
Three Youtube reviewers have broken their replaceable cutters on the Arc: Maxlvledc, HVAC Budget and Ink&Iron. There is a notch at the base of the Arc's cutters which is not found on the P4. That seems to be the culprit. You can see it happen with Ink&Iron.
Not a huge deal, but when Leatherman screws you on the MSRP, they dang well better not screw you with the product too. I'm predicting that they will be sending out replacement P4 cutters for the Arc. But time will tell.
-
-
If I am not mistaken the cutters used to be made from 154cm, they are now 440c. Don't know when they switched.
Could be the gap at the bottom of the cutters on the arc are larger.
-
Just saw this issue on YouiTube. Only seen one that chipped his cutter from deep recess cutting. Noticed Garage #5 has a slight hole too.
https://www.youtube.com/watch?v=bt19D8_dc5Y
So, being a lemming I decided to try this out too. Had to find a common wire coat hanger. First two cuts cut. Next three only crimped the wire.
Did a few more cuts that went through, and those that crimped just needed wiggling and they went ahead and cut.Seriously though, of all the Leatherman tools I have owned since the early 90's I never had to line up where I was cutting. Just threw the pliers up there and squeezed. There is a hard wire cutter with the ( ) recess, and the normal cutter. Do not do much wire cutting, yet still. Now we have to be careful how & where we cut with them?

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


I love all of the new Arc pics!