Loose scale fix
-
Hi Mitch,
If the scale is lifted slightly from the pins, then squeezing them back is what you need. I don't generally use a vise. I pad the scales up like you said, then use a small C-clamp. I can tighten down on just that one place and do it with a little more touch. I did just as you suggested with a Tinker a few weeks ago. Fixed it right up.
Unfortunately, this old 84mm has had the scales taken off several times by previous owners and the pockets for the pins are loose. Glue is about all that's left short of finding some new scales. I like to watch Felix Immler. He seems like a jolly sort of person.Hi Mac,
I know what you mean about the loose scale making you crazy. It doesn't affect the usefulness of the knife. (I used mine today to cut up some boxes for recycle.) I just have to tap the loose scale with a finger when I pick it up and hear it go 'tick'. Oh well, I guess I will just try something else to stick it down with. Or finally make some new scales.Best wishes to both of you. Gary
-
Will a tiny drop of superglue work?
-
@IMR4198 said:
I don't remember when the first loose SAK scale became an object of my attention. Been some time now. I have used automotive trim adhesive. Smells like model car glue. Used that on nylon. I have used contact cement. Ticklish to use. I have used epoxy. Works, but is permanent, more or less. What I wanted was-- To tighten up annoying loose scales on a SAK. Talking cellidor here.
- Non-permanent. Leave it be if I choose but still able to remove the scales.
- No scale damage or difficult clean up on the cellidor in case I decide to epoxy.
I am experimenting with ALEX. Painter's acrylic latex caulk. Comes in the tubes with a pointy end. What I am using is made by DAP and says ALEX on the side of the container. Squeeze out a little dab. Put a small amount into the scale mounting holes. Push it on. I didn't even clamp the one I have tried it on. Dries pretty fast, but needs a couple of days to firm up good. Doesn't smell and according to the Eastman Corp. doesn't harm cellidor. So far so good. Best wishes. Gary
;)
Might need a photo. Brace yourself. 84mm Tourist. Best wishes. G
[attach id=0 msg=2446139]
If you want it not to be permanent, I would suggest the use of bathroom sealant silicone. And, whenever removing celidor scales, put the knife in a cup of hot (from the boiler/kettle) water for 30sek before prying them off.
-
Thanks for the suggestions awl. I think one of the scales had been superglued at one time. This knife has been around. Silicone would probably work. I don't happen to have any on hand at the moment.
Mostly I just got annoyed at picking up the knife and feeling the scale click. My experimental fix is more like wrapping duct tape around a pipe. Temporary fix until something better comes to mind.
The little knife is strictly a utility item. The small size makes it a great carry. I will see if the current temporary fix is working well enough over the next little while. Best wishes. Gary

-
<-- Smiles in alox

;)
-
Thanks for the superglue tip folks!
I've got a couple of SAKs with "clicky" scales that drive me a little bonkers. I don't want to replace them, since there's nothing wrong with the scales otherwise, and applying pressure with some padding and a clamp didn't seem to do much.
I thought about something like superglue but didn't know how hard it would be to remove if/when it came time to replace the scales entirely.
-
I have been looking for something less permanent than epoxy and superglue. Might try some rubber cement if I can locate a bottle. I had made a longer reply, but decided to modify it. Best wishes. G
:D -
@marlowe221 said:
Thanks for the superglue tip folks!I've got a couple of SAKs with "clicky" scales that drive me a little bonkers. I don't want to replace them, since there's nothing wrong with the scales otherwise, and applying pressure with some padding and a clamp didn't seem to do much.
I thought about something like superglue but didn't know how hard it would be to remove if/when it came time to replace the scales entirely.
When it's time to replace the scales entirely just pop them off. There may be some plastic left in the ridge on the studs but it's easy enough to remove.
I'm generally a cheap old guy and for loose or cracked scales I just use Super Glue. If I have a larger chip I use some JB Weld.
-
@Helvetica Bold said:
Will a tiny drop of superglue work?I'm terribly weary of using super glue on Cellidor, that stuff melts/softens plastic. If there is any super glue that doesn't attack plastic it would be OK i guess.
But i usually prefer epoxy. But i just rub a tiny bit in the fixing slots "walls" , just enough for the barb on the bushing to grab around it. Never taken a glued one off, nut i guess it would not be that difficult..., even if i have to break the scale off...
-
@IMR4198 said:
Hi Mitch,
If the scale is lifted slightly from the pins, then squeezing them back is what you need. I don't generally use a vise. I pad the scales up like you said, then use a small C-clamp. I can tighten down on just that one place and do it with a little more touch. I did just as you suggested with a Tinker a few weeks ago. Fixed it right up.
Unfortunately, this old 84mm has had the scales taken off several times by previous owners and the pockets for the pins are loose. Glue is about all that's left short of finding some new scales. I like to watch Felix Immler. He seems like a jolly sort of person.Hi Mac,
I know what you mean about the loose scale making you crazy. It doesn't affect the usefulness of the knife. (I used mine today to cut up some boxes for recycle.) I just have to tap the loose scale with a finger when I pick it up and hear it go 'tick'. Oh well, I guess I will just try something else to stick it down with. Or finally make some new scales.Best wishes to both of you. Gary
I hate that 'ticky' sound. I have a Recruit that is doing it. When it happens I pull the scales off both sided and put a drop of super glue in each rivet hole on the scale and place a heavy box on it for an hour. Superglue hardens continuously as time goes on. If I ever have to break the scale off it will be because it has to be replaced due to chipping so I don't worry about it.
-
Would hot glue hold sufficiently?
Sent from my SM-G991U using Tapatalk
-
@marlowe221 said:
Thanks for the superglue tip folks!I've got a couple of SAKs with "clicky" scales that drive me a little bonkers. I don't want to replace them, since there's nothing wrong with the scales otherwise, and applying pressure with some padding and a clamp didn't seem to do much.
I thought about something like superglue but didn't know how hard it would be to remove if/when it came time to replace the scales entirely.
Yeah, I have a camper with a loose Stayglow scale (Shame they discontinued those.) I was thinking epoxy but I may try to add super glue instead. It’s too bad Victorinox doesn’t make interesting or plus scales cheap or easy to source.
-
You know, I never thought about using hot glue. Might work. Might not. Cellidor melts fairly easily. I think Barba might be on the right track with the silicone seal. That stuff has a very acidic smell to it before it cures. It makes me think twice. Some of this stuff should probably be tried out on a scrap scale first.
Lots of super glue suggestions out there. I personally wouldn't use it.
Mac says it melts the cellidor. He might be right. I don't have any on hand to try on a SAK scale. I don't remember whether I have ever pried the nylon scales from my 108mm. It is loose again. Scales are split too. It has been glued with several different things.
I will keep looking for a non-permanent attachment solution, I think. I used epoxy the last several times I stuck scales on. Padded up the surface and clamped it. Maybe I used some on the 108 nylon scales. I don't remember. Best wishes. G

-
There's lower temperature hot glues. I'd imagine that even the higher temperature ones can be applied to the metal first and then the scale attached without damaging the scale.
Sent from my SM-G991U using Tapatalk
-
Sounds like that could work. My last exposure to hot glue was when a friend tried to fix his broken hot glue gun with..... hot glue. I found a bottle of Elmer's wood glue in a box of seldom used things the other day. I thought about trying it. A brief internet search got an advisory from Elmer (or maybe Elsie) that their wood glue is a flop for plastic. There isn't a stick of hot glue in the house, or I might try heating a drop with a lighter or something. I have put my SAKs back in storage for now (challenge). Then I might experiment some more. Best wishes. Gary
8) -
Just throwing this out there: isn't there a "thick" Loc-tite for bolts with looser thread contact? I wonder how that might work.
Re: someone asking about "other Super Glues," Super Glue is a trade name for what is generically called CA glue or Cyanoacrylate. It is this chemical that eats the plastic. So there may be other glues that work, but CA glue, aka Super Glue or Cyanoacrylate, under any name or formulation (there is thin, medium, thick, gel, and colors), will unfortunately eat many plastics.
-
The only issues I've ever had with super glue and Celidor is when I got some on the outside of the scales. Sure the SG melts the Celidor a bit but I actually think that melting it around the studs is a good thing, helping it grab.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login