SAK-A-Like and/or off brand challenge for December?
-
I'm just here to follow along for now.... I won't be able to get to my SAKalike for the first third of the challenge, unfortunately.
-
I'm not sure what mine is but I do know it's from Voss Cutlery. I've tried doing research on it but I haven't found much. I do know that Voss Cutlery has been a round for a while but it sounds like it changed ownership down the road somewhere. If anyone could tell me anything about it, I'd be most appreciative.
I picked this up from the Revived Sos Surprise Box GAW ( US edition ) thread in case anyone is wondering.
Thus far, I've straightened out the bail, cleaned up some surface staining, lubricated all the moving parts, and filed down the back tool nail openings some more as I had a hard time getting my nails in there to open them. The corkscrew is a bit odd as it looks like a drill bit but seems to work pretty good at creating holes. It looks like the tip of the corkscrew is broken but I'm not positive as the only other example I found on eBay seems to look the same way.
The blade is 72mm long and it was as dull as a spoon when I got it. I had to start with a coarse stone but it took an edge very well. It passed the paper test but I'd like to strop it and see if I can get it a bit sharper. Just need to get me a strop or a thick strip of leather.
The file/flat head combo tool is 65mm long. The flat head is almost 1mm thick and 6mm wide at the end. I still need to try and take a brass brush to the file to see if I can clean it up more.
The awl is 39mm long and reminds me a lot of the old school SAK awls. That's what drew me to this piece to begin with.
The wrench opens up to about 17mm before it starts feeling weak or unstable, though I don't think you'd be able to get enough leverage to remove a nut or bolt of that size.
It also weighs 4.5oz so it's not light but it doesn't feel like I'm carrying a rock in my pocket.
I've thought about modding it but I'm not sure I have the skill set for it yet. :D I'll wait till after the challenge though as I don't have another SAK-A-Like. Ideally, I'd like to try the following mods:
-
powder coat the outer case a matte red
-
perhaps some brass pins but I'm not sold on that yet
-
cut a wire stripping notch at the back end of the file
-
swap out the corkscrew for the SAK longer in-line phillips
-
acid etching the square shaft of the wrench
-
acid etching only the file section of the combo tool
Looking forward to this challenge.



-
-
Definitely a cool gadget! I look forward to seeing you put it through its paces.
Day 1
Used the blade a few times today without taking a pic. Have the "old belt" test. Here's the T4 and a Tinker with the holes they poked in my old belt. The lock and front facing made the T4 more convenient to use, but the questionable edge made it pretty rough at actually making the hole. Overall, I think I'd rate it above the Tinker, but below a Vic 93mm or most other quality scout patterns.


-
@AzteCypher said:
I'm not sure what mine is but I do know it's from Voss Cutlery. I've tried doing research on it but I haven't found much. I do know that Voss Cutlery has been a round for a while but it sounds like it changed ownership down the road somewhere. If anyone could tell me anything about it, I'd be most appreciative.I picked this up from the Revived Sos Surprise Box GAW ( US edition ) thread in case anyone is wondering.
Thus far, I've straightened out the bail, cleaned up some surface staining, lubricated all the moving parts, and filed down the back tool nail openings some more as I had a hard time getting my nails in there to open them. The corkscrew is a bit odd as it looks like a drill bit but seems to work pretty good at creating holes. It looks like the tip of the corkscrew is broken but I'm not positive as the only other example I found on eBay seems to look the same way.
The blade is 72mm long and it was as dull as a spoon when I got it. I had to start with a coarse stone but it took an edge very well. It passed the paper test but I'd like to strop it and see if I can get it a bit sharper. Just need to get me a strop or a thick strip of leather.
The file/flat head combo tool is 65mm long. The flat head is almost 1mm thick and 6mm wide at the end. I still need to try and take a brass brush to the file to see if I can clean it up more.
The awl is 39mm long and reminds me a lot of the old school SAK awls. That's what drew me to this piece to begin with.
The wrench opens up to about 17mm before it starts feeling weak or unstable, though I don't think you'd be able to get enough leverage to remove a nut or bolt of that size.
It also weighs 4.5oz so it's not light but it doesn't feel like I'm carrying a rock in my pocket.
I've thought about modding it but I'm not sure I have the skill set for it yet. :D I'll wait till after the challenge though as I don't have another SAK-A-Like. Ideally, I'd like to try the following mods:
- powder coat the outer case a matte red
- perhaps some brass pins but I'm not sold on that yet
- cut a wire stripping notch at the back end of the file
- swap out the corkscrew for the SAK longer in-line phillips
- acid etching the square shaft of the wrench
- acid etching only the file section of the combo tool
Looking forward to this challenge.



Thats awesome Aztec, at first glance I thought that could be some calipers instead of a wrench. Interesting tool you have there.
-
<u>Day 1</u>
Only mail call duty today for my Voss. However, I need to change the tire tube on my daughter's bicycle tomorrow so that'll be a great opportunity to try out the wrench.

I also just noticed this today. The back part of the wrench sticks out a hair over a millimeter. I imagine that's by design and not sloppiness in manufacturing but I wonder what it would be for. I feel like I could use it as a tiny hammer but who knows.

-
@BPRoberts said:
Definitely a cool gadget! I look forward to seeing you put it through its paces.Day 1
Used the blade a few times today without taking a pic. Have the "old belt" test. Here's the T4 and a Tinker with the holes they poked in my old belt. The lock and front facing made the T4 more convenient to use, but the questionable edge made it pretty rough at actually making the hole. Overall, I think I'd rate it above the Tinker, but below a Vic 93mm or most other quality scout patterns.
Is the tip on the T4 sharp enough to cut the hole or do you have to drive it through?
-
I kinda want to participate challenge but carrying my T4 for long time i cant justify carrying it anymore. I must admit i hate that blade and its my main reason why i dont want to carry anymore, all other tools opens smoothly except Blade, i can open it better with my left hand by opening halfway with my index finger and rest with thumb but knife is in left hand and i need to change it to right hand to operate with it.
Blade feels really stiff to open but any other tool doesnt. Blade itself is ok when used, it doesnt blow your mind but does it work.
It kinda feels too small for me to operate properly, even that its same size as my Pioneer X but since pivots are closer center it makes opening tools bit uncomfortable also opening tools on blade side feels painful cause of blade. Since blade doesnt open pressing end of tool it feels sometimes panful when blades back stays in place when opening packet opener/prying tool and File/flathead.Tools itself is quite good, scissors can handle all kind stuff but not puncturing precision cut, scissors are comfortable use. Awl is good packet opener, screwdriver and letter opener but shape of awl makes it feel not good for drilling (allways when i did it i was affraid breaking it and i didnt even try to make same mowevements what i would do SAK awl.
Phillips was maybe my most used tool, its long, strong and feels like its centered.
File is ok, its bit short file but its quite aggressive so it removes burrs and mater fairly fast. Medium flathead is ok but i would try same torque with as phillips.
Packet opener/prying tool is good for prying stuff and used slot key but openening packets is bit controversial, it works but since it has thick flathead it doesnt have sharp edge like on Spirits chisel so it needs bit diffrent angle to work properly.
Pocketclip is nice addition to it and tool feels pretty good in hand altought it looks bulky.Only Tools Matters
-
@AzteCypher said:
Is the tip on the T4 sharp enough to cut the hole or do you have to drive it through?Not entirely sure I understand this question. Best answer I can give is that I had to push harder than with most the other awls I've tested on this belt.
-
Day 1
@BPRoberts said:
I’ve been thinking of getting a Fox Vulpis, so hoping to see one of those.Ask and ye shall receive!
I have several tools I’m hoping to show and perhaps put through a few tests during this challenge, but I’ll start with the Fox Vulpis. This is the version that has the knife blade, saw, scissors, can opener + screwdriver, and bottle opener + screwdriver, and Ti scales.
F&F are excellent. W&T also good with about average pull (which is fine with me; I don’t personally consider gator-snap pull necessary or even desirable in a carry knife).
For a MT with a tool loadout that bears more than a passing resemblance to the Vic Huntsman and Farmer X, perhaps one of the most noticeable aspects is how small this knife is. At only about 74 mm closed, I can get at most three fingers on the handle. More on this later…

-
Excited to see it in action! Thanks for stepping in.
-
@BPRoberts said:
Not entirely sure I understand this question. Best answer I can give is that I had to push harder than with most the other awls I've tested on this belt.The awl on the SAKs come to a point where as on the T4 it appears to be a flat head.
I was just wondering if the flat head on the T3 came to a sharp edge to allow you to slice into the leather belt or if it was just a regular flat head. Sounds like it's just a regular flat head as you mentioned that you had to push harder that usual.
Sorry for the confusion.
-
I'm interested to see how a T4 works out in a challenge. I don't have one, but I have been looking.

-
It's all good! I'll get a close up later, but I would say it's really closer to a chisel than anything else. There's some light angling "horizontally" and a pretty aggressive edge "vertically". When I went scout-crazy a couple months ago, I found a few others that used a similar design. IMO, it's an acceptable compromise as an awl, provided that it works alright as a screw driver, and the tip isn't weakened too badly to bend (making it no longer usable as a driver) or break. We'll see how it does throughout the month.
-
Day 1
SAK-Alike Challenge
Leatherman Free T2I'll join in BP, but will be a day behind unless I can catch up somewhere along the line.
I picked up this T2 back in the spring at the local flea market. It is also quite chunky and I really haven't carried it because of that. I can see that I really need to work on its edge as well. This challenge will give "me" a chance to really give "it" a chance. Heck, I might even break down and buy a pocket clip for it.
I also have an Armbar that might make a cameo over the next 30 days.

-
Glad to have you aboard. Let me know what you decide on the pocket clip, I could probably pass mine along.
-
Day 2
Continuing with the awl, I decided to try the sd tip on my glasses. It was able to tighten and loosen the screw, with some scraping. I guess if I was ever stranded in the wilderness and needed to tighten my glasses, it'd work. Awlso closeup of the awl.



-
Day 2
The main blade of the Vulpis is of course M390, which is arguably one of the primary draws of this knife. It came suitably sharp right from the factory.
I’m not a huge fan of the unusual blade shape. I suppose I might describe it as a modified lambsfoot, but the pics speak for themselves. Call it personal preference, but I would rather have a clip point or spear point if it is to be my only blade.
Some dislike nail cutouts as opposed to nail nicks (mainly based on aesthetics, I believe), but functionally I find no difference.
The blade can be pinched open, which I appreciate as it can be a nail saver if you’re using the knife frequently.
The Vulpis easily trimmed my cigar today.
While I didn’t have a chance to try it on these tasks today, if we think about this Vulpis as a competitor to the Vic Huntsman and FX as a hiking/camping tool, I believe that the shorter blade of the Vulpis makes it less suited for kitchen/food use, and the shorter handle would make it more difficult to use as a whittling/woodworking knife.


-
@BPRoberts said:
Awlso closeup of the awl.I understand the T4 awl now. It's definitely more of a chisel. Thanks for the close up.
@nate j said:
The Vulpis easily trimmed my cigar today.That's a good use right there. I need to try that during this challenge.
<u>Day 2</u>
The wrench worked pretty good at getting the nut off the bicycle. I was trying to get a video using only one hand but I kept fumbling it so I just gave up and took a picture instead.
However, anything bigger than this bicycle nut and it would be a little bit of struggle to generate enough torque to get the nut or bolt off. Not to mention that the wrench wouldn't open too much more before coming loose.

-
This is my explanation why I will not join this challenge :
-
@nate j said:
Day 2The main blade of the Vulpis is of course M390, which is arguably one of the primary draws of this knife. It came suitably sharp right from the factory.
I’m not a huge fan of the unusual blade shape. I suppose I might describe it as a modified lambsfoot, but the pics speak for themselves. Call it personal preference, but I would rather have a clip point or spear point if it is to be my only blade.
While I can appreciate your personal opinion,,,,, I really like the shape of the main blade. I bet it will prove quite effective at many tasks!

@AzteCypher said:
The wrench worked pretty good at getting the nut off the bicycle.bike repair for the kiddos, doesn't get much better than that!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login